Local Guide · Residential solar installers
Roof Direction, Tilt and Shade: Will Solar Work on My House?
South is best, but east and west roofs work in Texas and Florida. Shade matters more than direction. Here is how to model your own roof, read a shade report, and handle trees, HOAs and neighbors.
Your panels do not have to face south. In Texas and Florida, south gives the most yearly output, southeast and southwest are close behind, and east or west roofs produce somewhat less but still work. Shade is the bigger problem: an unshaded east or west roof often beats a shaded south one. Run the free PVWatts calculator for each roof face and ask the installer for a per-panel shade report before you sign.
Key facts
- FSEC says south-facing arrays are best, east- or west-facing arrays produce a little less, and north-facing arrays should generally be avoided.
- FSEC: shading is the primary killer of PV production; aim for no shade from 9 a.m. to 3 p.m. on the winter solstice.
- Berkeley Lab: in 2023, 56% of new U.S. home solar systems faced south and 23% faced west.
- PVWatts models 1,421 kWh per kW per year in Houston and 1,568 in Tampa for a south-facing 20 degree array.
- Texas Property Code 202.010(d)(5)(B): an HOA cannot designate a roof area if another spot raises estimated output by more than 10% in NREL's PVWatts.
- Florida Statute 163.04(2): an HOA may choose the roof location only facing south or within 45 degrees east or west of due south.
- Austin Energy's ERCOT energy component of Value of Solar fell from $0.1005/kWh in FY2022 to $0.0280/kWh in FY2025.
- Florida Statute 163.045 bars local permits or fees for removing a residential tree an ISA arborist documents as an unacceptable risk.
- Texas Local Government Code 212.905 bars city tree mitigation fees for trees under 10 inches in diameter at an owner's one- or two-family home.
- Florida Statute 704.07 allows written, recordable solar easements to keep a solar device exposed to the sun.
Do solar panels have to face south?
No. South is best in Texas and Florida because the sun spends most of the day in the southern sky, but east- and west-facing roofs work too. The University of Central Florida's Florida Solar Energy Center (FSEC) puts it simply in its consumer guide: south-facing arrays are best in the northern hemisphere, east- or west-facing arrays "are fine as well, but do produce a little less energy," and north-facing arrays should generally be avoided.
Shade matters more than direction. The same FSEC guide says "the primary killer of PV system production is shading" and that "it is far more important to have an unshaded array than to have one that is perfectly oriented to due south." A clear east or west roof often beats a shaded south roof.
Most real systems are not perfectly south. Berkeley Lab's Tracking the Sun report found that in 2023, 56% of new U.S. home systems faced roughly south and 23% faced west. So if your best roof faces west, you are in good company.
Directions in degrees
Solar designers describe direction as azimuth, measured clockwise from north: north is 0 degrees, east is 90, south is 180 and west is 270. Southeast is 135 and southwest is 225. You will see these numbers on proposals, shade reports and the free PVWatts calculator.
| Roof direction | Azimuth | General verdict in Texas and Florida |
|---|---|---|
| South | 180 | Best yearly output |
| Southeast or southwest | 135 or 225 | Very close to south |
| East or west | 90 or 270 | Works; somewhat less yearly output. West shifts output to the afternoon. |
| North | 0 | Usually avoided; only consider on very low-slope roofs after modeling |
How much less? It depends on your exact roof pitch and location, so model your own roof (steps below). As a published reference point, an EnergySage article quoting the U.S. Department of Energy's Solar Energy Technologies Office gives an example for an 18 degree roof in San Diego: east-facing panels lost 15% and west-facing panels lost 10% of yearly output compared with south, and panels turned 10 degrees off ideal lost less than 1%. That example is from California, not Texas or Florida. Our states sit farther south (Houston is near 29.8 degrees latitude and Miami near 25.8), where the sun rides higher in the sky, so direction generally matters a bit less here. Do not rely on any rule of thumb when a free model of your actual roof takes five minutes.
How to check your own roof in PVWatts (step by step)
PVWatts is a free calculator from the national lab now called the National Laboratory of the Rockies (formerly NREL). Utilities and Texas law use it: Texas Property Code 202.010 names "a publicly available modeling tool provided by the National Renewable Energy Laboratory" as the yardstick in HOA placement disputes, and CPS Energy's rebate manual told installers to show design output with PVWatts. FSEC's consumer guide walks homeowners through it too.
- Enter your address. PVWatts pulls typical weather data for your location.
- System size: start with 1 kW DC so the answer is "kWh per kW." Multiply later.
- Module type: standard.
- Array type: FSEC advises "Fixed (roof mount)" for rooftop systems and "Fixed (open rack)" for ground mounts.
- System losses: leave the default 14% unless your installer gives you a better number.
- Tilt: for a roof, the tilt equals your roof pitch (table below).
- Azimuth: your roof's direction in degrees (180 for south, 270 for west and so on). Use a phone compass app standing parallel to the roof edge, or the aerial view in a map app.
- Run it, then change only the azimuth to compare each roof face. The difference in yearly kWh is your direction penalty.
Roof pitch to tilt, from FSEC
| Roof pitch (rise/run) | Tilt in degrees |
|---|---|
| 4/12 | 18.4 |
| 5/12 | 22.6 |
| 6/12 | 26.6 |
| 7/12 | 30.3 |
| 8/12 | 33.7 |
| 9/12 | 36.9 |
| 10/12 | 39.8 |
| 12/12 | 45.0 |
Baseline output for a south roof at 20 degrees
We ran PVWatts version 8 for a 1 kW south-facing array at a 20 degree tilt with 14% losses. These are model estimates, not measured output, but they show the starting point before direction and shade.
| City | kWh per kW per year | City | kWh per kW per year |
|---|---|---|---|
| Houston | 1,421 | Miami | 1,552 |
| Dallas | 1,506 | Tampa | 1,568 |
| Austin | 1,483 | Orlando | 1,544 |
| San Antonio | 1,497 | Jacksonville | 1,455 |
Multiply your direction-adjusted result by your planned system size, then compare it with your yearly use. See what size solar system do I need?.
Does an east-west roof work for solar?
Yes. Many Texas and Florida homes have a ridge that runs north to south, so the two big roof faces point east and west. Splitting the panels across both faces works well in many cases.
- Daily shape: east panels make more in the morning and west panels more in the afternoon. Together they spread output over more of the day instead of a midday spike.
- Yearly total: lower than the same panels facing south, so you may need a few more panels to make the same kWh. Your PVWatts runs tell you how many.
- Inverters: panels on different faces see different sunlight at the same moment. A string inverter needs each face on its own input (called an MPPT, a tracker that finds each string's best operating point), or the design can use microinverters or optimizers. See string inverters vs microinverters.
Whether the lower yearly total costs you money depends on how your utility values each kWh, explained in the next section.
Does a west-facing roof help with Texas peak prices?
Sometimes. It depends on your utility and plan.
In Texas, more solar on the grid means midday power is worth less, while late afternoon and early evening, when air conditioning peaks and solar fades, can be worth more. Austin Energy's own numbers show the trend: in its April 2026 Value of Solar update, the ERCOT energy part of the solar credit fell from $0.1005 per kWh (fiscal 2022) to $0.0280 per kWh (fiscal 2025). That component reflects what solar's energy was worth on the ERCOT market.
| Your setup | Is west-facing worth more per kWh? | Why |
|---|---|---|
| Texas REP plan with a fixed buyback rate | Partly | Exports earn the same rate any time, but west panels line up better with your own late-afternoon AC use, and power you use directly saves your full retail rate. |
| Texas plan with a wholesale-based buyback or time-of-use rates | Often yes | Late-day kWh can be priced higher. Read the plan's rules before you count on it. |
| Austin Energy Value of Solar | No, for the credit | Austin credits 100% of production at one rate (12.89 cents per kWh for fiscal 2027 to 2029), no matter the hour. |
| CPS Energy and co-ops | Check the tariff | Each sets its own rules. |
| Florida IOU net metering (FPL, Duke, TECO) | Little difference | Rule 25-6.065 nets your use and exports over the billing month, so timing within the day barely changes your bill. |
| JEA and newer OUC customers | Somewhat | Exports earn less than retail, so panels that produce when you are using power (often afternoons) are worth more. |
West-facing panels also help with batteries in a different way: less battery is needed to cover the evening if your panels are still making power at 6 p.m. See Texas solar buyback plans, Texas utility solar programs and ERCOT, solar and batteries.
How does roof tilt affect output in Texas and Florida?
Tilt matters less than direction and shade. Most home roofs are close enough. An EnergySage summary of Department of Energy guidance gives a sweet spot of roughly south-facing at 15 to 40 degrees of tilt, which covers most pitched roofs from about 4/12 to 10/12.
- Latitude tilt: FSEC says ground-mounted systems are usually tilted at the site's latitude, using Cocoa, Florida at 28.5 degrees as its example. Latitude tilt maximizes yearly output for a fixed array.
- Flatter roofs: at low latitudes like South Florida, a flatter tilt gives up less than it would up north, because the sun is high most of the year. Rain still needs to wash the panels, so very flat arrays can collect more dirt. See solar panel maintenance and cleaning.
- Steep roofs: steep south roofs do slightly better in winter and slightly worse in summer.
- Flat roofs and tilt racks: tilting panels up on a flat roof adds wind load, which is a big deal in Florida's High Velocity Hurricane Zone. Miami-Dade lists racking not rated for the roof's wind pressure zones among the most common reasons PV plans get rejected. See can solar panels survive a hurricane?.
If your roof is steep, slate, tile or flat, read solar on tile, metal, flat and shingle roofs.
How much production does a north-facing roof lose?
More than any other direction, which is why FSEC says north-facing arrays should generally be avoided. On a low-slope north roof the penalty shrinks, because nearly flat panels see much the same sky whichever way they lean. On a steep north roof it grows quickly. The EnergySage article quoted one installer estimating north-facing systems make sense in about "one out of 1,000 installs."
Rules that matter:
- CPS Energy's rebate manual said systems facing a northern direction did not qualify for its rebate, and that the system should be on the most southern-facing side.
- In Texas, an HOA may designate where panels go on your roof, but not if an alternate location would raise estimated yearly production by more than 10% in the NREL PVWatts tool (Property Code 202.010(d)(5)(B)). If your HOA tries to push panels onto a north face, run PVWatts for both faces and print the results.
- In Florida, an HOA may pick the roof spot only within an orientation to the south or within 45 degrees east or west of due south, and only if that does not impair the collectors' effective operation (s. 163.04(2)).
See HOA solar rules in Texas and Florida.
How much does shade reduce production?
Shade cuts output far more than its size suggests. Panels are wired together, and on a simple string system a shaded panel can drag down the others on the same string. Shade sources around Texas and Florida homes include:
- Live oaks, pines, palms and pecans, which keep growing after the system goes up
- Your own chimneys, vent pipes, dormers and satellite dishes
- A neighbor's second story or a new house on an empty lot next door
- Low winter sun angles, when shadows are longest
The solar window
FSEC's example design calls for no shade on the array between 9 a.m. and 3 p.m. on the winter solstice, when shadows are longest. That is a good test for your roof. It also says to "consider the future growth of vegetation" during the site survey, so a young tree that is fine today may not be fine in five years.
Shade reports, solar access and TSRF
Installers measure shade with software or an on-roof tool and report it in a few ways:
- Solar access: the share of available sunlight that reaches the panel after shading. Oncor's solar incentive program asked for this number and defined the shading percentage as 100 minus solar access. For example, 95% solar access means 5% shading.
- TOF (tilt and orientation factor): how the panel's tilt and direction compare with the ideal for that site.
- TSRF (total solar resource fraction): solar access and TOF combined, the share of the ideal yearly sunlight the panel actually gets.
Ask for the report for every array, not just a summary. Check that the tilt, azimuth and panel counts match the proposal. Oncor's program listed mismatched tilt, azimuth and panel counts between shade studies, photos and paperwork as common reasons it sent projects back, which tells you these errors happen. CPS Energy's manual let it deny rebates for "excessive shading or poor orientation" and require a documented shade analysis. See how to read a solar proposal.
Can microinverters or optimizers fix shading?
They reduce the damage but cannot create sunlight. With microinverters (one small inverter per panel) or DC optimizers (a box on each panel feeding a string inverter), each panel works on its own, so one shaded panel does not pull down the rest. FSEC notes that some technologies can reduce the effects of partial shading and that a good contractor will run a shading analysis.
Use them when shade hits only some panels at some hours, or when panels sit on several roof faces. They do not help much if the whole array is shaded for hours, and they add parts on the roof that may need service later. Panel-level electronics also help meet the National Electrical Code's rapid shutdown rule (section 690.12), which limits voltage on rooftop wiring so firefighters can work safely. Compare designs in string inverters vs microinverters vs optimizers and check panel options in types of solar panels.
If production drops over time, new shade is a common cause. See why is my solar producing less than expected?.
Should I cut down trees for solar?
Sometimes, but think it through. Shade trees also cool your home and lower AC use, which is the biggest load in Texas and Florida. Losing a tree that shades a west wall can raise your cooling bill even as solar lowers it. A better first step is often trimming, or putting panels on a different roof face, a garage or a ground mount.
Questions to ask before you remove a tree
- How many kWh a year does the shade cost? Ask the installer for a shade report with and without the tree.
- What does the tree do for cooling? A tree shading the west side of the house in summer may be worth keeping.
- Can trimming solve it? Removing a few limbs may open the 9 a.m. to 3 p.m. window.
- Is the tree protected by your city? Many cities regulate tree removal. Check before you cut.
- Is the tree a hazard anyway? A storm-risk tree near the roof can also damage panels in a hurricane.
Florida tree law
Florida Statute 163.045 says a local government may not require a notice, application, approval, permit, fee or mitigation for pruning, trimming or removing a tree on residential property if the owner has documentation from an ISA-certified arborist or a Florida licensed landscape architect that the tree poses an unacceptable risk to persons or property. "Residential property" here means a single-family detached home. The local government may not require you to replant. The exception does not cover mangroves. Shade on solar panels by itself is not a "risk to persons or property," so for a healthy tree, follow your city or county tree ordinance.
Texas tree law
Texas Local Government Code 212.905 limits city tree fees. A city may not charge a tree mitigation fee for removing a tree that is on an existing one- or two-family home that is your residence and is less than 10 inches in diameter at 4.5 feet above the ground. A city that charges mitigation fees must let you apply for a credit for planting trees to offset the fee. Cities can still have tree ordinances and permits, especially for large or protected trees, so call your city's planning or development office before removing a big tree.
Does a neighbor's tree have to be trimmed for my solar?
Generally no. We found no Texas or Florida statute that forces a neighbor to trim or remove a tree to protect your solar panels' sunlight. Your HOA rights under Texas Property Code 202.010 and Florida Statute 163.04 protect your right to install solar, not your access to sunlight across a neighbor's lot.
Solar easements in Florida
Florida does let neighbors agree, in writing, to protect sunlight. Under Florida Statute 704.07, a solar easement to keep a solar energy device exposed to the sun must be in writing and can be recorded like other property documents. The document must describe both properties, the vertical and horizontal angles of the easement in degrees, where it sits on the neighbor's land, the point it is measured from, terms for ending it, and any payment. An easement like this can protect against a future tree or building, but your neighbor has to agree. Have a real estate attorney draft it.
Practical steps
- Talk to your neighbor first. Many will agree to trimming, especially if you pay for a licensed arborist.
- Check your HOA documents. Some communities have tree or view rules that may help or hurt.
- Design around trees you cannot control: use the faces with clear sky, or a ground mount in the sunniest part of the yard.
- For a dispute over a tree that is a real hazard to your house, talk with an attorney. This page is general information, not legal advice.
Can I put panels on a garage, patio roof or the ground instead?
Often, yes. If your main roof faces the wrong way, is shaded, or is too small or too old, look at other spots.
- Detached garage or shop: may face a better direction. The wiring run back to your main panel adds cost, and the structure must be able to carry the load.
- Patio cover or carport: must be engineered for the panels and for wind. In Florida, wind design is critical, and Palm Beach County's expedited permit checklist, for example, uses a 170 mph design wind speed with engineered attachment details for every part of the load path.
- Ground mount: lets you pick the best direction and tilt, away from trees. FSEC suggests a latitude tilt for ground arrays. It needs yard space and trenching, and in Texas HOA communities, Property Code 202.010 lets the HOA bar ground-mounted devices taller than the fence line and those outside a fenced yard or patio. See ground-mounted vs roof-mounted solar.
- Not enough room anywhere? Community solar subscriptions may be an option. See community solar in Texas and Florida.
Roof condition, direction and shade together: a quick decision guide
| Your situation | What usually makes sense |
|---|---|
| Unshaded south, southeast or southwest roof in good shape | Ideal. Get quotes. |
| Unshaded east and west faces | Use both faces; expect a modestly larger system for the same kWh; check how your plan values afternoon power. |
| South roof shaded part of the day | Get a shade report per panel; consider microinverters or optimizers; compare with an unshaded east or west face. |
| Heavily shaded roof all day | Trim, use a ground mount or another structure, or consider community solar. Do not pay for panels that will sit in shade. |
| Roof needs replacing within a few years | Re-roof first. See should you replace your roof before solar?. |
| Only a north face available | Model it; usually look elsewhere. |
| HOA wants panels on a worse face | Run PVWatts for both; Texas has the 10% rule, Florida the within-45-degrees-of-south rule. |
Before you size anything, cut your usage. Every kWh you save is a kWh you do not have to squeeze onto a tricky roof. See efficiency upgrades before solar.
What to ask the installer about direction and shade
- Which roof faces will you use, and what is the azimuth and tilt of each?
- Can I see the shade report for each array, including solar access and TSRF?
- What yearly production do you estimate for each face, and what tool did you use? Can I check it in PVWatts?
- What happens to production when the trees on my lot grow? Did you model future growth?
- Why did you choose a string inverter, microinverters or optimizers for my shade conditions?
- If my HOA asks for a different location, will you model the difference for me?
- Do you guarantee production, and how is a shortfall measured and paid?
- Does your design meet the local wind code for my roof zones?
How to choose a provider
- Find each roof face's azimuth with a compass or map app.
- Convert your roof pitch to tilt with the FSEC table.
- Run PVWatts at 1 kW for each roof face and compare yearly kWh.
- Check the 9 a.m. to 3 p.m. winter sun window for shade from trees and buildings.
- Ask installers for a per-array shade report with solar access and TSRF.
- Confirm the tilt, azimuth and panel counts in the shade report match the proposal.
- Decide on microinverters or optimizers if shade hits some panels part of the day.
- Check how your utility or plan values afternoon power before favoring west.
- Price trimming before removing a shade tree, and check city tree rules.
- If your HOA picks the location, print PVWatts runs for both spots.
- Consider a garage, carport, ground mount or community solar if the roof will not work.
Related residential solar installers guides
- String Inverters vs Microinverters vs Optimizers: Which Fits a Texas or Florida Home?
- HOA Solar Rules in Texas and Florida: What Your HOA Can and Cannot Do
- Ground-Mounted vs Roof-Mounted Solar: Which Is Better for a Texas or Florida Home?
- What Size Solar System Do I Need? How Many Panels for a Texas or Florida Home
- How Do I Read and Compare a Solar Proposal?
- How Do Texas Solar Buyback Plans Work Without Net Metering?
- Before You Go Solar: Efficiency Upgrades That Shrink the System You Need
Residential solar installers by state and city
Questions people ask
Do solar panels have to face south?
No. South gives the most yearly output in Texas and Florida, but east and west roofs work well too. The Florida Solar Energy Center says east- and west-facing arrays are fine but produce a little less, and that an unshaded array matters far more than perfect south orientation. Berkeley Lab found 23% of new U.S. home systems in 2023 faced west. Run PVWatts for your own roof to see the difference.
How much less does a west-facing roof produce?
It depends on your pitch and location, so model your own roof in PVWatts. As a published example, the U.S. Department of Energy's solar office, quoted by EnergySage, found west-facing panels on an 18 degree San Diego roof lost about 10% of yearly output compared with south, and east-facing lost about 15%. Texas and Florida are farther south, where direction usually matters a bit less.
Does a west-facing roof help with Texas peak prices?
It can. West panels produce more in the late afternoon, when Texas AC use peaks. If your plan pays a wholesale-based buyback or uses time-of-use rates, those late-day kWh may be worth more, and power you use directly saves your full retail rate. In Austin, where all output is credited at one Value of Solar rate, the hour does not change the credit.
How does roof tilt affect output in Florida?
Less than you might think. Florida's low latitude means the sun is high most of the year, so most pitched roofs between about 4/12 and 10/12 do well. FSEC uses latitude tilt (about 28.5 degrees in Cocoa) for ground mounts. Flat roofs with tilt racks add wind load, which is a major design issue in South Florida.
What is a TSRF or solar access report?
It is a shade study for your roof. Solar access is the share of available sunlight that reaches the panels after shading. The tilt and orientation factor (TOF) compares your roof's angle and direction with the ideal. TSRF, total solar resource fraction, combines the two. Ask for the report for each array and make sure the tilt, azimuth and panel counts match the proposal.
Should I cut down trees for solar?
Only after you weigh what the tree does for you. Shade trees cool your house and cut AC use. Ask the installer for production with and without the tree, consider trimming or using another roof face, and check your city's tree rules. In Florida, s. 163.045 removes permit requirements only for trees an arborist documents as an unacceptable risk. In Texas, Local Government Code 212.905 limits mitigation fees for small trees at your home.
Does my neighbor have to trim a tree that shades my panels?
Generally no. We found no Texas or Florida law that forces a neighbor to trim trees for your solar access. Your HOA solar rights protect your right to install panels, not sunlight across another lot. In Florida, neighbors can sign a recorded solar easement under s. 704.07 to protect sunlight. Talk with your neighbor and, for an easement, a real estate attorney.
Can microinverters fix shading problems?
They limit the damage. With microinverters or optimizers, each panel works independently, so one shaded panel does not drag down the rest of the string. They help most when shade hits a few panels for part of the day or the array spans several roof faces. They cannot make shaded panels produce, so a heavily shaded roof is still a poor site.
Can my HOA make me put panels on a worse roof?
Only within limits. In Texas, an HOA may designate the roof area unless another location would raise yearly production by more than 10% in NREL's PVWatts tool (Property Code 202.010). In Florida, an HOA may pick a spot facing south or within 45 degrees east or west of south, as long as it does not impair effective operation (s. 163.04). Print PVWatts runs for both locations.
Is a north-facing roof ever worth it?
Rarely. North is the worst direction in Texas and Florida, and FSEC says north-facing arrays should generally be avoided. A very low-slope north roof loses less than a steep one, so it may be worth modeling if you have no other space. CPS Energy's rebate manual did not rebate north-facing systems. Consider a ground mount or community solar instead.
Sources
- UCF Florida Solar Energy Center: Installing a solar electric system
- Berkeley Lab: Tracking the Sun 2024 executive summary
- EnergySage: Solar panel orientation and angle (updated Nov 1, 2024)
- PVWatts v8 Houston run (NLR)
- PVWatts v8 Dallas run (NLR)
- PVWatts v8 Austin run (NLR)
- PVWatts v8 San Antonio run (NLR)
- PVWatts v8 Miami run (NLR)
- PVWatts v8 Tampa run (NLR)
- PVWatts v8 Orlando run (NLR)
- PVWatts v8 Jacksonville run (NLR)
- Texas Property Code chapter 202
- Florida Statutes 163.04
- Florida Statutes 163.045
- Florida Statutes 704.07
- Texas Local Government Code chapter 212
- Austin Energy Value of Solar update (April 2026)
- Austin Energy: Value of Solar rate
- CPS Energy Solar Rebate Program Manual (2019)
- Oncor 2023 Solar Program kickoff presentation
- Florida Administrative Code Rule 25-6.065
- JEA: Distributed generation
- OUC: How to apply for solar for your home
- Miami-Dade PV solar permitting workshop
- Palm Beach County expedited solar checklist
- Mike Holt: NEC 690.12 rapid shutdown
This guide was written by our editorial team from the public sources listed above. It is general information, not legal advice; confirm licensing and terms directly with any provider.


