Local Guide · Hurricane shutters and impact windows
How Do You Hurricane-Proof a Garage Door? Bracing Kits, Reinforcement Struts, Jamb Anchoring and When to Replace
The garage door is usually the biggest opening on a house, and when it fails, wind pressure can lift the roof. Here is what the codes and the garage door industry say about braces, struts, posts and replacement in Florida and Texas, and what actually counts for permits and insurance.
The most reliable way to hurricane-proof a garage door is to replace the door and track with a system rated for your home's design wind pressure, and in windborne debris areas with an impact rating under ANSI/DASMA 115, installed with properly anchored jambs. Bracing kits and struts help only if the door's manufacturer specifies them or they carry a product approval. Parking a car against the door does not reinforce it.
Key facts
- IBHS calls re-roofing and installing a wind-rated garage door the two most significant ways to improve a home's hurricane resilience. (IBHS / FORTIFIED)
- IBHS says a garage door pushed in by wind lets pressure build inside the home, pushing up on the roof and out on the walls. (IBHS / FORTIFIED)
- TDI states that in recent hurricanes garage door failures contributed to 80 percent of home failures; TDI does not cite a study for that figure. (Texas Department of Insurance)
- TDI says Texas garage doors must be tested to ASTM E330 and glass panels rated to ASTM E1996. (Texas Department of Insurance)
- Florida requires garage door glazed opening protection in windborne debris regions to meet an approved impact-resisting standard or ANSI/DASMA 115, and replacement garage doors must comply with Chapter 16 of the Florida Building Code. (FBC 1609.1.2.3; FBC Existing Building 707.4)
- Since the 2021 International Residential Code, garage doors must carry a permanent manufacturer label showing the model, positive and negative design wind pressure, installation drawing number and test standard. (DASMA TDS 1502, quoting IRC R609.4.1)
- The garage door industry association says positioning a vehicle against a garage door does not reinforce it and may damage the vehicle and the door. (DASMA TDS 152)
- DASMA warns that a post or other reinforcement not purchased from or specified by the door manufacturer may not result in a door that properly resists the wind. (DASMA TDS 153)
- Miami-Dade requires a stand-alone permit for garage door replacement with the door area, an elevation of each wall, and the current NOA or Florida approval for each door. (Miami-Dade County)
- TWIA lists garage doors among improvements that need a windstorm Certificate of Compliance for TWIA eligibility. (TWIA)
Why is the garage door so important in a hurricane?
A two-car garage door covers an opening roughly 16 feet wide. Long spans of relatively light material flex under wind. TDI notes that garage doors are particularly vulnerable because of the long span they cover and the lightweight material they are made of.
When a garage door blows in or is pulled out, wind rushes into the garage. IBHS explains that the trapped pressure pushes up on the roof and out on the surrounding walls, often causing significant structural damage. That is why IBHS calls installing a wind-rated garage door one of the two most significant hurricane upgrades a homeowner can make, alongside re-roofing.
Other organizations agree on the direction, with caveats on the numbers:
- TDI states that garage door failures contributed to 80 percent of home failures in recent hurricanes. TDI does not cite the study behind that figure, so treat it as TDI's statement rather than a measured statistic.
- The nonprofit Federal Alliance for Safe Homes (FLASH) has shifted its message from calling garage doors "the largest and weakest opening" to saying "a storm-ready garage door is your best and strongest defense." FLASH cites a NIST study of 3,000 homes hit by the 2011 Joplin tornado that found homes with intact garage doors far more likely to keep their roofs and the wall next to the garage. That is tornado data, not hurricane data, but it supports the same physics.
Why do garage doors open by themselves in storms?
DASMA's technical sheet on securing garage doors explains a finding from Hurricane Andrew in 1992: many doors investigators assumed had been left open were actually forced open by the wind. Garage door tracks tilt slightly back, and the top rollers sit in the curved part of the track. Wind pushing on the door face can create an upward force that drives the door open. Wind-resistant doors and manual locks are designed to resist that.
Wind load rating vs impact rating: what is the difference?
Garage doors can be rated for two different things, and you may need one or both.
| Rating | What it means | Test standards | Where it is required |
|---|---|---|---|
| Wind load (pressure) rating | The door resists a stated positive (inward) and negative (outward) pressure, in pounds per square foot (psf) | ANSI/DASMA 108 or ASTM E330 | Required by modern codes for garage doors in Florida and in Texas jurisdictions that enforce the IRC, and by TDI for windstorm certification |
| Impact rating | The door (or its glass) also survives windborne debris impact followed by cyclic pressure | ANSI/DASMA 115 (garage and rolling doors); ASTM E1996 for glass panels | Glazed garage doors in windborne debris regions; also earns the top Florida wind mitigation rating for garage doors |
Key points from DASMA's wind load FAQ (TDS 168) and its sheet on IRC labels (TDS 1502):
- Both directions matter. Positive pressure pushes the door in; negative pressure pulls it out. Both ratings are listed.
- Pressure, not mph. Doors are tested to pressures. Wind speed is only one input; exposure category, door size and location, mean roof height, building shape and the code in force all change the required pressure. A door sold as "rated for 150 mph" without psf numbers is not a code rating.
- Test load is higher than design load. The test load in ANSI/DASMA 108 is commonly 1.5 times the design load.
- Two-story houses often need higher ratings because wind pressure increases with height.
- The building department decides. DASMA says the local building authority is the sole and final determiner of your door's required wind load.
What do Florida's codes require for garage doors?
Florida's rules come from the Florida Building Code (FBC), 8th Edition (2023):
- Glazed garage doors in windborne debris regions must have glazed opening protection that meets an approved impact-resisting standard or ANSI/DASMA 115 (FBC Building 1609.1.2.3; FBC Residential R301.2.1.2). Florida's windborne debris region is the area within 1 mile of the coast where the design wind speed is 130 mph or more, plus anywhere it is 140 mph or more.
- Replacement garage doors must be designed and built to comply with Chapter 16 of the FBC Building (FBC Existing Building 707.4). That means current wind pressures, not what the old door was built to.
- No engineer needed for a like-for-like swap. Sealed drawings are not required to replace garage doors on an existing one- or two-family home or townhouse if the new units are installed per the manufacturer's instructions for the wind zone, meet current FBC Residential design pressures, are the same size in the same opening, and a copy of the instructions comes with the permit application (FBC Building 107.1.1).
- Product approval. Doors must carry a Florida product approval or, in Miami-Dade and Broward's High-Velocity Hurricane Zone (HVHZ), the approval the county accepts. Miami-Dade accepts Florida Building Commission approvals as well as its own Notices of Acceptance (NOAs).
Look up approvals yourself before signing a contract. See Florida product approval lookup and Miami-Dade NOA lookup. The full impact garage door picture is in hurricane-rated garage doors.
What does Texas require for garage doors on the coast?
Texas has two separate tracks:
- Local building code. Cities such as Houston, Galveston and Corpus Christi adopt their own editions of the International Residential Code. DASMA notes that the 2021 IRC (and later editions) requires garage doors to be tested to ASTM E330 or ANSI/DASMA 108 and to carry a permanent wind load label (R609.4 and R609.4.1). Ask your building department which edition it enforces and whether a permit is required.
- TDI windstorm certification for TWIA eligibility. In the 14 first-tier coastal counties and the parts of Harris County east of State Highway 146 in La Porte, Morgan's Point, Pasadena, Seabrook and Shoreacres, TWIA lists garage doors among improvements that need a Certificate of Compliance. Since April 1, 2026, TDI certifies work to the 2024 IRC or IBC.
TDI's guidance for garage doors:
- Garage doors must be tested to ASTM E330, and glass panels should be rated to ASTM E1996.
- Most major garage door manufacturers have product listings with TDI. If the door has glass panels, consider an impact-resistant door.
- Garage door assemblies must be installed strictly per the manufacturer's installation instructions for their tested high-wind application, which typically come as drawings.
- For help finding wind and impact ratings for garage door products, call TDI at 800-248-6032, option 3.
- TDI advises not making final payment until the contractor finishes and TDI issues the WPI-8 certificate.
See TDI windstorm certification and Texas coastal building codes.
Does a new garage door need a wind load sticker?
Under the 2021 and later International Residential Code, yes. Section R609.4.1, as quoted by DASMA, says garage doors must have a permanent label from the manufacturer identifying:
- The garage door manufacturer
- The model or series number
- The positive and negative design wind pressure rating
- The installation instruction drawing reference number
- The applicable test standard
DASMA adds that third-party labeling is not required by that code text, the label does not have to be applied at the factory, and doors that are not wind load rated do not get a wind load label. The 2021 and 2024 International Building Codes have the same labeling rule for non-residential buildings.
Practical uses of the label:
- Photograph it right after installation. It is evidence for your permit file, your TDI or Florida wind mitigation inspection and any insurance claim.
- Match the installation drawing number on the label to the drawing the installer followed. A wind-rated door installed with the wrong anchors or track is not a wind-rated installation.
- Do not paint over or remove the label.
What are the options for hurricane-proofing an existing garage door?
TDI describes two basic ways to strengthen a garage door opening: replace the door and track with a system designed for high winds and windborne debris, or use a tested and approved impact-resistant covering. In practice, homeowners also ask about reinforcement kits, posts and braces. Here is how they compare:
| Option | What it is | Strengths | Limits |
|---|---|---|---|
| Replace door and track | New wind-rated (and, where needed, impact-rated) door, track, springs and anchors as one tested system | Meets current code; clear documentation; best for insurance credit | Largest project; needs permit, and in coastal Texas a WPI-8 for TWIA |
| Manufacturer reinforcement package | Struts, heavier hinges, springs and track specified by your door's manufacturer for your model | Can upgrade an existing door's wind rating if the manufacturer offers it | Only for models with such a package; adds weight; needs a trained technician |
| Vertical post (brace) system | Removable posts from floor to header, engaged before a storm | Can stiffen a door when horizontal struts are not enough | Must be specified by the manufacturer to be reliable; homeowner must install before each storm; loads the header |
| Approved impact covering | Panel or fabric screen system approved for the garage opening size | Adds debris protection without replacing the door | Must be installed before each storm; must hold an approval for that opening |
| Aftermarket brace not specified by the door maker | Generic kit bought separately | Low cost | DASMA warns it may not make the door properly resist wind; may count as component substitution |
Do garage door braces work?
They can, when they are part of a tested system. The Door and Access Systems Manufacturers Association (DASMA) is direct about the limits:
- Manufacturer-integrated or manufacturer-supplied posts are common options. With integrated systems, the homeowner secures the post with a crank or lever; with supplied systems, the homeowner follows an assembly procedure from the manufacturer.
- Aftermarket posts are different. DASMA's TDS 153 warns that a post or any product not purchased from or specified by the door manufacturer may not result in a door that properly resists the wind, and may constitute a component substitution. Contact the door manufacturer to assess any aftermarket brace.
- Posts move load to the header and floor. Vertical posts transmit wind forces to the opening header and the garage floor, while the door still loads the side framing where the track attaches. DASMA recommends a qualified design professional assess the building structure before installing vertical reinforcement.
- You have to use them. The homeowner must install or engage the posts before every hurricane or high-wind warning. DASMA says the electric opener should usually be unplugged while posts are in place, so no one runs the door into the braces.
- Inspectors want them engaged. If a building inspector must inspect a vertically reinforced door, the reinforcement should be installed and fully engaged at inspection.
Bottom line: a brace system specified for your exact door, with a structurally adequate header and floor, is a legitimate tool. A generic brace bought online and bolted to an old, unrated door is not a substitute for a rated door.
Are garage door braces approved for code or insurance credit?
We could not confirm that any aftermarket garage door brace, by itself, earns code compliance or a Florida insurance credit. Here is how the rules work, so you can check a specific product:
Florida wind mitigation form (OIR-B1-1802)
- The form's opening protection question rates the weakest protection on the house, including garage doors.
- Level A for garage doors means verified cyclic pressure and large missile performance under ANSI/DASMA 115, and products must be listed in the Florida or Miami-Dade product approval system.
- Level D covers verified non-glazed entry or garage doors that show wind pressure compliance with ASTM E330, ANSI/DASMA 108 or PA/TAS 202.
- Openings that need replacement do not qualify for wind mitigation rate differentials.
DASMA's sheet on Florida insurance factors (TDS 188) adds that a non-glazed, wind-load-compliant door that is not impact rated neither earns nor removes an opening protection credit, while a glazed garage door that is not impact resistant can pull the whole house down. It also says an impact-resistant garage door increases the credit where it is part of overall opening protection.
So, for a brace or reinforcement kit to matter for insurance, the door-plus-kit combination generally needs documentation the inspector can verify: a Florida product approval or Miami-Dade NOA that covers the configuration, or a manufacturer document showing the reinforced door's tested rating. Ask the seller for the approval number, then look it up. If they cannot give one, assume no credit.
Texas
For TWIA eligibility, a garage door replacement needs a WPI-8. TDI accepts products tested to its required standards and listed through product evaluation or approval. Before buying any retrofit kit for a coastal Texas home, ask the TDI windstorm program (800-248-6032) or your appointed engineer whether that kit can be certified on your door.
Can I add struts to my existing garage door?
Only if your door's manufacturer offers a reinforcement package for your model, and it should be installed by a trained door technician. DASMA explains that manufacturers commonly use horizontal struts to make doors wind resistant, but it also warns (TDS 152) that adding reinforcement increases the door's weight and may cause failure or collapse of tracks and other parts not designed for the load. Upgrading by adding reinforcement can require a package that includes appropriate springs, hardware and track.
DASMA's sheet on adding weight (TDS 176) explains why: springs are sized for the door's original weight. Extra weight can unbalance the door, break springs, overwork the opener, or twist the horizontal track so the door falls out. Garage doors weigh anywhere from about 90 to more than 500 pounds, so a door leaving its track is dangerous.
Do not add struts, wood bracing or steel angle on your own. Do not touch springs, cables or bottom brackets; they are under extreme tension. Ask the manufacturer or an authorized dealer whether a reinforcement package exists for your door, what wind rating it achieves, and whether it changes the door's label or approval.
Why do jambs, headers and tracks matter as much as the door?
A rated door attached to weak framing is not a rated opening. DASMA's TDS 152 says the attachment of both the door track and the door jamb to the structure is just as critical as the strength of the door itself. If you question your door's ability to resist high winds, have a design professional evaluate both the door and the surrounding frame of the opening.
DASMA's TDS 161, Connecting Garage Door Jambs to Building Framing, gives maximum anchor spacings for wind loads from 10 to 60 psf, depending on door width, wood species (Southern Pine or Spruce-Pine-Fir) and anchor type. The fastener types it covers include:
- 1/4 inch by 3 inch self-tapping anchors and 3/8 inch by 3 inch sleeve anchors into concrete or masonry
- 3/8 inch by 3 1/2 inch expansion anchors and 7/16 inch by 8 inch L-bolts
- 3/8 inch by 3 inch lag screws and 16d common nails into wood
- Welds and self-tapping screws into steel framing
For existing concrete block homes, common in Miami, Tampa and South Texas, TDS 161 advises locating steel reinforcement before drilling, using structural drawings or pilot holes, and never drilling through or damaging the reinforcement. It also says professional engineering advice should be obtained for jamb attachment.
DASMA's FAQ adds that the supporting structure to which the jambs attach is the general contractor's responsibility, not the door installer's. If your installer doubts the framing, that question should go to a contractor, engineer or building official before the new door goes in. When you get quotes, ask each one: "Are you replacing or re-anchoring the jambs to the manufacturer's high-wind drawing?"
Retrofit vs replace: which makes sense?
| Your situation | Usually the better path |
|---|---|
| Old door with no wind label, rusted track, or damaged sections | Replace door and track with a rated system |
| Door has glass panels that are not impact rated, in a windborne debris region | Replace with an impact-rated door, or add an approved impact covering |
| Door is wind rated but you want debris protection or a better Florida credit | Approved impact covering, or an impact-rated replacement |
| Manufacturer offers a reinforcement package for your model and the door is in good shape | Manufacturer retrofit by a trained technician, with documentation |
| Generic brace kit and an unrated door | Not recommended as a substitute for replacement |
| Coastal Texas home that needs TWIA eligibility | Whatever option TDI can certify with a WPI-8; confirm before buying |
What does it cost?
We do not publish installed prices for wind-rated garage doors or retrofit kits because we found no named, dated source for them. For context only: the 2025 Cost vs. Value report prices a standard garage door replacement defined as a 16 by 7 foot, four-section, R-12 insulated steel door on new heavy-duty galvanized tracks, which is not a wind-rated specification. A FLASH consumer survey reported by DASMA found 34 percent of respondents would spend $500 to $1,000 on an upgraded door, which reflects willingness to pay, not actual prices. Get at least three written quotes listing the exact door model, its design pressures, its approval number and the jamb work included.
Can a grant help?
Florida's My Safe Florida Home program can pay for garage door improvements when recommended by its inspection. The statute lists garage doors among eligible opening protection improvements, and the program may require all openings to be improved as a condition of the grant. The state pays up to $10,000 on a $2 state to $1 homeowner match for eligible applicants, with no match for low-income applicants. Its portal has been unavailable since November 10, 2026 for a platform move. See My Safe Florida Home windows and doors.
Do I need a permit for a garage door replacement?
Usually yes, in both states.
- Miami-Dade: A stand-alone permit for garage door replacement requires a completed building permit application (Category 22) with the total square feet of doors being installed, a contact sheet, an elevation of each exterior wall showing which doors are being replaced and their sizes, and the current NOA or Florida product approval for each door. Owner-builders need an additional form.
- Tampa: Even after a declared disaster, when the city waives permits for some size-for-size exterior door swaps, a permit is always required for garage door replacement. The fee is waived while the Mayor's emergency powers are in effect, but the Residential Building Trade permit is still needed.
- Elsewhere in Florida: Orlando, Jacksonville and other cities have their own permit portals; plan on a permit and product approval for any garage door replacement.
- Texas: Ask your city building department. On the coast, the TDI windstorm certification for TWIA is a separate requirement; a city permit does not replace it.
See Florida window and door permits.
Can I park my car against the garage door?
No. This is one of the most common hurricane myths. DASMA's sheet on garage doors and high wind events says positioning a vehicle against a garage door is not recommended: it does not reinforce the door and may damage both the vehicle and the door. Wind loads act across the whole face of the door and push it inward or pull it outward. A car bumper touching the bottom section does not resist those forces.
DASMA's other storm-day advice:
- Close the door and leave it closed before the storm. An open door leaves walls, ceiling and roof vulnerable.
- If your door has a manual lock, engage it, and disconnect the opener while the door is locked.
- Unlock the door before using the opener again; running the opener against a locked door can damage both.
- Do not operate the door during high winds; the extra force needed can injure people and damage the door.
- Do not hang weight or improvised bracing from the door or tracks.
Are fabric garage door screens a hurricane option?
They can be. TDI's second option for garage doors is a tested and approved impact-resistant covering, and fabric screens and panels designed for garage openings exist. The key questions are:
- Does the screen hold a Florida product approval or Miami-Dade NOA (or a TDI-accepted evaluation on the Texas coast) for an opening the size of yours?
- Does the approval require specific anchors on the house and at the slab? Those anchors must be installed permanently and correctly.
- Does the screen deflect into the door when loaded? The approval and installation instructions set required clearances.
- Will you be home to install it? Like panels, a screen protects only if it is deployed before the storm.
An approved covering adds debris protection but does not by itself change your door's wind pressure rating. See fabric hurricane screens.
What about coastal flood zones and storm surge?
On barrier islands and low-lying coastal lots, flood rules can override wind-load choices. DASMA notes that in some coastal areas subject to storm surge, other requirements may apply, and it publishes separate guidance on garage doors in breakaway construction (TDS 184). If your garage is below the base flood elevation in a coastal high hazard area, such as parts of Galveston Island, Bolivar, South Padre or the Florida Keys, ask your floodplain administrator what is allowed before buying a heavy, highly reinforced door.
How do I check my garage door after a storm?
DASMA's TDS 174 gives an owner's inspection sequence. Start inside with the door closed, a flashlight and a step stool. Check alignment and glass, the jambs and header attachment, track fasteners, rollers, roller brackets and hinges, the spring system (look only) and every door section for cracks, dents or buckling. Then pull the opener disconnect, unlock the door and lift slowly. Stop if the door is heavy, binds or a lock is under tension. If anything looks wrong, close the door gently and call a trained door technician. Photograph damage before repairs for your insurance claim. See damage claims and repairs.
How to choose a provider
- Find the wind load label on your current door; if there is none, assume it is not rated.
- Ask your building department (or TDI on the Texas coast) for the design pressure your opening requires.
- Get quotes for a complete rated door, track, springs and jamb anchoring, with positive and negative psf ratings listed.
- In Florida, get the product approval or NOA number and look it up; in Texas, confirm TDI can certify the door.
- If considering a brace or strut kit, confirm it is specified by your door's manufacturer for your model.
- Have a design professional check the header and jambs before adding vertical posts.
- Pull the permit (Miami-Dade Category 22; Tampa requires one even after disasters) and, on the Texas coast, file for the WPI-8.
- Photograph the new door's label and installation for your records.
- Before each storm: close, lock if equipped, engage any posts, unplug or disconnect the opener.
- Do not park a car against the door or add improvised bracing.
- After a storm, run DASMA's owner inspection; leave springs to a technician.
Related hurricane shutters and impact windows guides
- What Is a Hurricane-Rated Garage Door? Wind Load vs. Impact Ratings, Bracing Kits and How to Read the Label
- Do Fabric Hurricane Screens and Storm Curtains Really Work?
- Wind Mitigation Form OIR-B1-1802: How Is Opening Protection Graded (Classes A, B, C, N, X)?
- Does My Safe Florida Home Pay for Impact Windows and Doors? 2026 Eligibility, Match and Status
- Do You Need a Texas Windstorm Certificate (WPI-8) for New Windows, Doors or Shutters?
- Florida Product Approval (FL Number): How Do You Search floridabuilding.org and Verify Windows, Doors and Shutters?
- Do You Need a Permit for Impact Windows, Doors and Shutters in Florida? Process, Documents, Fees and Inspections
- What Should You Do After a Hurricane Breaks Your Windows or Damages Your Shutters? Claims, Repairs and Code Upgrades
Hurricane shutters and impact windows by state and city
Questions people ask
How do I hurricane-proof my garage door?
Start by checking for a wind load label. If there is none, the most reliable upgrade is a complete wind-rated door and track system matched to your required design pressures, impact-rated if it has glass or if you want the top Florida insurance rating, installed with jambs anchored to the manufacturer's high-wind drawing. If replacement is not possible yet, use only reinforcement or bracing specified by your door's manufacturer, or an approved impact covering, and get a permit.
Will a garage door brace lower my Florida insurance?
Not by itself, as far as we could confirm. The OIR-B1-1802 form rates garage doors at Level A only with verified ANSI/DASMA 115 impact and cyclic performance and a listing in the Florida or Miami-Dade approval system, and at Level D for verified wind pressure compliance on non-glazed doors. A brace with no approval or tested documentation gives the inspector nothing to verify. Ask for the approval number before you buy.
What is the difference between ANSI/DASMA 108 and 115?
ANSI/DASMA 108 is a test method and acceptance criteria for garage doors under uniform static air pressure, which is the basis for a door's positive and negative wind load ratings. ANSI/DASMA 115 adds windborne debris impact followed by cyclic pressure, which is what makes a garage door impact rated. Florida requires impact protection for glazed garage doors in windborne debris regions, and the 1802 form gives its top garage door rating only for DASMA 115 doors.
Do I need an impact-rated garage door if it has no windows?
In Florida's windborne debris regions outside Miami-Dade and Broward, the code's impact requirement for garage doors applies to glazed openings, and DASMA's Florida insurance sheet says non-glazed garage doors there do not have to be impact resistant for the 1802 form. They still need a wind pressure rating. An impact-rated door can raise your mitigation credit. Miami-Dade and Broward's HVHZ rules are stricter, so ask your building department.
Does a garage door replacement need a TDI windstorm inspection?
On the Texas coast, yes if you want TWIA eligibility. TWIA lists garage doors among improvements that need a Certificate of Compliance. File the WPI-1 notice before work starts so a TDI inspector can inspect during installation, or hire an appointed engineer. TDI advises holding final payment until the WPI-8 is issued. A city permit, where required, is a separate step.
Can I reinforce my garage door myself?
Not safely in most cases. DASMA advises owners not to add reinforcement themselves, because added weight can unbalance the springs and cause the track to fail, and it warns that springs and anything fastened to them are under extreme tension. Owners can close and lock the door, engage manufacturer-supplied posts, and follow the manufacturer's storm instructions. Struts, springs and track changes belong to a trained door technician.
Is a wind-rated garage door the same as a hurricane door?
Not exactly. A wind-rated door resists a stated wind pressure. A door marketed for hurricanes should also list its design pressures and, ideally, an impact rating under ANSI/DASMA 115, plus a Florida approval or NOA or a TDI listing. Without those numbers and approvals, a "hurricane" label is marketing. Check the permanent wind load label required by the 2021 and later IRC.
Sources
- IBHS / FORTIFIED: Before the Storm, a Homeowner's Guide to Hurricane Readiness
- Texas Department of Insurance: Making repairs after a storm
- Texas Department of Insurance: Questions to Ask Your Contractor Before Installing Opening Protection
- Texas Department of Insurance: Adopted windstorm codes
- TWIA: Windstorm Certification
- DASMA, Door + Access Systems, Spring 2025: Garage Doors' Storm Appeal on the Rise (FLASH interview)
- DASMA TDS 152: Garage Doors and High Wind Events
- DASMA TDS 153: Vertically Reinforcing Sectional Garage Doors for Wind Load Conditions
- DASMA TDS 161: Connecting Garage Door Jambs to Building Framing
- DASMA TDS 168: Wind on Garage Doors, Frequently Asked Questions
- DASMA TDS 174: Building Occupant, Checking a Residential Sectional Garage Door for Damage
- DASMA TDS 176: Adding Weight to a Garage Door Assembly
- DASMA TDS 183: Garage Door Component Substitution
- DASMA TDS 188: Insurance Mitigation Factors for Homeowners Purchasing Garage Doors in Florida
- DASMA TDS 192: Securing Garage Doors During High Wind Events
- DASMA TDS 1502: The International Residential Code and Wind Load Labels
- Florida Building Code, Building 2023, Chapter 16 (1609.1.2) (UpCodes)
- Florida Building Code, Building 2023, Chapter 1 (107.1.1) (UpCodes)
- Florida Building Code, Existing Building 2023, Chapter 7 (707.4) (UpCodes)
- Florida OIR Uniform Mitigation Verification Inspection Form OIR-B1-1802 (Rev. 04/26)
- Miami-Dade County: Windows, Shutters, Doors and Security Bars
- City of Tampa: Post-Hurricane Permitting Guide (2026)
- Florida Statutes s. 215.5586: My Safe Florida Home Program
- JLC / Remodeling 2025 Cost vs. Value: Garage Door Replacement
- My Safe Florida Home
This guide was written by our editorial team from the public sources listed above. It is general information, not legal advice; confirm licensing and terms directly with any provider.


