Local Guide · Hurricane shutters and impact windows
Hurricane Shutters for Mobile and Manufactured Homes: HUD Wind Zones, Options, Tie-Downs and Why You Still Evacuate
You can put hurricane shutters on a mobile or manufactured home, but they do not make it a safe place to ride out a hurricane. Here is how HUD wind zones work in Florida and Texas, which shutter types fit thin walls and siding, why tie-downs matter more, and what state law says about installers, parks, insurance and grants.
Yes, many mobile and manufactured homes can take hurricane shutters, panels or fabric screens, as long as they attach to the wall framing and not just the siding. But shutters do not make a mobile home safe to stay in. Florida's Division of Emergency Management says people in mobile homes should follow all evacuation orders, and the National Weather Service says a mobile home is not a safe tornado shelter. The home's HUD wind zone, shown on its data plate, and properly installed tie-downs matter more than window protection.
Key facts
- Federal rules (24 CFR 3280.305) set three HUD wind zones: Zone I (standard loads of 15 psf horizontal), Zone II (100 mph design wind speed) and Zone III (110 mph).
- In Florida, HUD places Broward, Charlotte, Collier, Dade, Franklin, Gulf, Hendry, Lee, Martin, Manatee, Monroe, Palm Beach, Pinellas and Sarasota counties in Wind Zone III and all other Florida counties in Wind Zone II.
- In Texas, HUD and Texas law (Occupations Code s. 1201.256) place Aransas, Brazoria, Calhoun, Cameron, Chambers, Galveston, Jefferson, Kenedy, Kleberg, Matagorda, Nueces, Orange, Refugio, San Patricio and Willacy counties in Wind Zone II; all other Texas counties are Zone I.
- Every HUD-code home's data plate must state the wind zone it was designed for (24 CFR 3280.305(c)(4)).
- For Zone II and III homes, HUD's design pressures for exterior windows and sliding glass doors are plus or minus 38 psf (Zone II) and 46 psf (Zone III) in most wall areas, higher near corners.
- Florida requires anyone who installs a mobile home to hold a state mobile home installer's license (s. 320.8249), and installation must follow uniform state rules for resisting wind, flood and overturning (s. 320.8325).
- Florida lets insurers give up to a 10% discount to mobile home owners who show a current inspection certifying tie-downs are properly installed and in good condition (s. 627.0629(7)).
- My Safe Florida Home requires a site-built home, so mobile and manufactured homes are not eligible (s. 215.5586).
- Florida's Division of Emergency Management says people in a mobile home should follow all evacuation orders.
Can you put hurricane shutters on a mobile home?
Usually, yes. Mobile and manufactured homes have windows and doors like any house, and shutters, panels and fabric screens can be fitted to them. The difference is the wall. Many manufactured homes have thinner wall framing and vinyl or metal siding over sheathing, so the shutter's fasteners must reach solid framing, not just the siding. A shutter is only as strong as what holds it on.
Before you buy anything, understand what shutters can and cannot do on a manufactured home:
- They can keep debris from breaking windows and sliding doors, which keeps rain and wind out and protects what is inside while you are evacuated.
- They cannot keep the home from being lifted, rolled or shifted. That is the job of the anchoring and tie-down system.
- They cannot make the home safe to shelter in during a hurricane. You still evacuate.
A quick note on words. People say "mobile home" for any factory-built home on a chassis. Federally, homes built to the HUD code since June 15, 1976 are "manufactured homes." Texas law defines the HUD label as a device attached to each transportable section of a HUD-code manufactured home constructed after June 15, 1976. Florida's statutes still use "mobile home" in many places. Modular homes are different again: in Florida they are "manufactured buildings" approved under the state building code program rather than the HUD code, and IBHS treats them like single-family homes for FORTIFIED.
What are HUD wind zones, and which zone is my home?
Federal construction standards at 24 CFR 3280.305 divide the country into three wind zones. A manufactured home is built for one of them, and the zone is printed on the home's data plate.
| Zone | Design basis in 24 CFR 3280.305 | Where in Florida | Where in Texas |
|---|---|---|---|
| Zone I | At least 15 psf horizontal wind load and 9 psf net roof uplift | None | All counties not in Zone II, including Harris (Houston), Dallas, Bexar (San Antonio) and Travis (Austin) |
| Zone II | Designed by an engineer or architect for a 100 mph design wind speed (ASCE 7-88, Exposure C) or HUD's pressure table | All counties not in Zone III, including Orange (Orlando), Hillsborough (Tampa) and Duval (Jacksonville) | Aransas, Brazoria, Calhoun, Cameron, Chambers, Galveston, Jefferson, Kenedy, Kleberg, Matagorda, Nueces, Orange, Refugio, San Patricio, Willacy |
| Zone III | Same method at a 110 mph design wind speed | Broward, Charlotte, Collier, Dade (Miami-Dade), Franklin, Gulf, Hendry, Lee, Martin, Manatee, Monroe, Palm Beach, Pinellas, Sarasota | None |
Two surprises in that table. First, Harris County, home to Houston, is Zone I under HUD and Texas law, even though Houston has taken serious hurricane hits. Second, the HUD design speeds (100 and 110 mph) are based on an older standard, ASCE 7-88, and are not directly comparable to the much higher "ultimate" wind speeds used for site-built homes in the current Florida Building Code. Do not compare the numbers one to one.
How to read your data plate
Under 24 CFR 3280.305(c)(4), the data plate must show the wind and roof load zones the home was designed for, or the actual design loads if it was built for more, plus reproductions of the zone maps. The data plate is usually inside a kitchen cabinet, a bedroom closet or near the electrical panel. Take a photo of it. You will need it for shutters, insurance and any FORTIFIED or engineering review.
Texas rules on where homes can go
Texas Occupations Code s. 1201.256 says a manufactured home built on or after September 1, 1997 must meet HUD Wind Zone II standards to be installed in a Zone II county. Homes built before that date may be installed in Zone I or II counties without restriction. A retailer selling a post-1997 Zone I home must warn the buyer in writing that it was not built to withstand hurricane-force wind in a Zone II or III area and cannot be installed in a Texas Zone II county.
What shutters work on manufactured homes?
The same product families used on site-built homes, with more attention to attachment. See types of hurricane shutters for the full comparison.
| Type | Fit for manufactured homes | Main concern |
|---|---|---|
| Fabric or mesh screens | Often a good fit: light weight, low load on the wall | Must be anchored per the product approval; they flex toward the glass |
| Polycarbonate or aluminum panels | Common; panels are light enough for one person | Need permanent anchors or tracks fastened into framing |
| Accordion shutters | Possible on sturdier walls and sliding doors | Permanent weight on the wall; tracks must hit framing |
| Roll-down shutters | Possible, but the box and guides are heavy | Wall must carry the hood and guide loads; engineering often needed |
| Plywood | Emergency only | Screws into siding alone will not hold; see below |
The key point is the product approval. In Florida, approved shutters come with installation instructions that list approved substrates (wood framing, concrete, steel) and fastener spacing. If your wall is not one of the approved substrates, the approval does not cover your installation. Ask the seller to show you, in the approval document, the substrate and anchor that match your home. In Texas, ask for the product evaluation and installation instructions the same way. See Florida product approval lookup and Miami-Dade NOA lookup.
Who installs shutters on a mobile home?
Florida's state mobile home installer license (s. 320.8249) is for setting up the home itself: placing it, connecting sections and anchoring it. Shutters are a different trade. Florida's specialty structure contractor category (rule 61G4-15.015) covers installing hurricane protection devices, and general, building and residential contractors can do the work within their scopes. Ask your county or city building department whether a permit is required for shutters on a manufactured home, and who may pull it. In Texas, check with your city or county, and in TDI's coastal catastrophe areas ask TDI whether the work falls under windstorm certification for your structure.
Are impact windows available for mobile homes?
Impact-rated windows are made in standard sizes for site-built openings. Some can be fitted to manufactured homes, but the rough openings, wall thickness and framing in a manufactured home can be different, and an impact window is approved only when it is installed in the tested way into an approved substrate. That makes impact windows harder to use on manufactured homes than shutters or screens.
If you are considering impact windows for a manufactured home:
- Ask for the product approval and its installation drawing, and check that it lists a substrate like yours.
- Check the design pressure against your home's wind zone. For Zone II and III homes, HUD's table sets design pressures for exterior windows and sliding glass doors of plus or minus 38 psf (Zone II) and 46 psf (Zone III) in most wall areas, and 48 psf and 58 psf within 3 feet of corners.
- Expect that framing changes may be needed, and that changing the home's structure may raise questions with the manufacturer or state regulator. Ask before you cut.
The Chronicle found no named, dated cost study for impact windows or shutters on manufactured homes, so we do not quote prices. Get at least two written quotes that list each opening, the product approval and the anchoring method. See how to compare quotes.
Is plywood safe on manufactured home siding?
Plywood is an emergency measure on any home, and on a manufactured home it has extra problems. Vinyl or thin metal siding cannot hold a screw against wind suction. If the screws do not reach studs or a solid header, the panel can tear off and become debris itself.
The Florida Building Code allows 7/16-inch wood structural panels as opening protection on some site-built one- and two-family homes, but only with a maximum 44-inch span between fastener lines, panels cut to overlap the wall at least 2 inches beyond the fasteners, and permanently installed corrosion-resistant anchors. For wood-frame walls, those anchors must be sized to 1/4-inch lag screws with at least 300 pounds of design withdrawal capacity. That code section is written for site-built homes. It is a useful benchmark for how serious the attachment needs to be, not an approval for your manufactured home.
If plywood is your plan:
- Find the framing around each window now, before a storm, and mark it.
- Pre-cut and label every panel by window, and pre-drill holes that line up with framing.
- Install permanent anchors in framing, not in siding, so you are not drilling new holes in a hurry.
- Practice on one or two windows, as TDI suggests for removable panels.
IBHS advises that plywood used as a last resort be at least 3/4 inch thick. That is heavier, so plan how you will lift it. See DIY plywood hurricane protection.
Do shutters make a mobile home safe to stay in during a hurricane?
No. This is the most important point on this page.
Florida's Division of Emergency Management says that people in an ordered evacuation zone, a low-lying flood area or a mobile home should follow all evacuation orders, and lists mobile homes among the places most likely to be evacuated. The Florida Climate Center at Florida State University notes that hurricane-force winds "can easily damage or destroy mobile homes and other non-permanent structures, often moving them well away from their foundations." National Weather Service storm reports after Hurricane Harvey in 2017 recorded several mobile homes destroyed in Refugio County, Texas.
Hurricanes also spin off tornadoes, and the National Weather Service's tornado safety guidance says plainly that a mobile home is not a safe shelter. Shutters do nothing against a tornado or against the home being moved off its piers.
What to do: know your evacuation zone (in Florida, floridadisaster.org/knowyourzone; in Texas, your county or city emergency management office), pick a destination ahead of time, close shutters and secure the home before you leave, and go when officials tell mobile home residents to go.
Tie-downs vs shutters: which matters more?
Tie-downs and anchoring, by a wide margin. A home that stays on its foundation with broken windows is repairable. A home that rolls is often a total loss.
Florida. Section 320.8325 requires the state to adopt uniform installation standards, and says the home must be installed on a permanent foundation that resists "wind, flood, flotation, overturning, sliding, and lateral movement." The owner is responsible for installation in accordance with department rules. Florida also requires every person who installs a mobile home to hold a state installer license under s. 320.8249, and local licenses do not substitute for it.
Texas. Occupations Code s. 1201.255 requires manufactured housing to be installed in compliance with the department's standards and rules, and the chapter requires foundation and anchoring systems that resist overturning and lateral movement for the wind zone the home was built for. Section 1201.101(d) says a person may not act as an installer without an installer's license. Under the chapter's definitions, the "department" is the Texas Department of Housing and Community Affairs operating through its Manufactured Housing Division, which is the agency to call about installers, installation and complaints.
Insurance ties in too. Florida s. 320.8325 says windstorm insurers may issue coverage only if the home has been installed per state rules. Citizens' eligibility for windstorm coverage includes mobile homes used as dwellings that are tied down in compliance with state tie-down requirements (s. 627.351). And s. 627.0629(7) lets insurers give up to a 10% discount to owners who show a current inspection certifying the tie-downs are properly installed and in good condition. Ask your insurer whether it offers that discount and what inspection it accepts.
Order of priorities
- Confirm the home's wind zone matches your county.
- Have the anchoring and tie-downs inspected and repaired by a licensed installer.
- Protect windows and sliding doors with approved shutters or screens attached to framing.
- Secure skirting, carports and sheds so they do not become debris.
- Evacuate when told.
Do mobile home parks have shutter rules?
Many do. In Florida, Chapter 723 governs mobile home parks where residents own the home and rent the lot. Section 723.035 requires the park's rules and regulations to be posted in the recreation hall or another conspicuous place, and bars rules from charging fees or fines except as provided in the park prospectus. Park rules commonly address exterior changes, storage and appearance, so ask the park office for its rules before you install permanent shutters, and get approval in writing if the rules require it.
If you rent the home itself, not just the lot, shutters are the landlord's call. Florida's s. 83.51 says a landlord is not required to maintain a mobile home owned by the tenant, so a tenant who owns the home and rents the lot is responsible for the home. See landlord and tenant shutter rules.
In Texas, park and community rules are set by the lease and community rules, so read them before you install.
Are mobile homes eligible for My Safe Florida Home grants?
No. Florida's My Safe Florida Home program, s. 215.5586, requires the home to be "site-built and owner-occupied" and homesteaded to qualify for a program inspection, and a grant requires eligibility for an inspection. A mobile or manufactured home is not site-built, so it does not qualify. Chapter 2026-174 rewrote parts of MSFH eligibility in 2026 but kept the site-built requirement in the statute text we reviewed. As of November 19, 2026, the MSFH site also says its applicant portal has been unavailable since November 10 while the program moves to a new platform. See My Safe Florida Home for windows and doors.
There is no matching statewide grant in Texas that we could find. Check with your county or city emergency management office for any local mitigation programs, and with your insurer for discounts.
Insurance: what changes when you add shutters to a manufactured home?
Florida law requires mobile home rate filings to include discounts for homes built to ASCE 7-88, the standard HUD adopted on July 13, 1994, that also meet state tie-down requirements (s. 627.0629(3)). That is one reason newer, wind-zoned homes often cost less to insure. Ask your insurer whether it credits shutters on a manufactured home; mitigation discounts for mobile homes vary by company.
Citizens Property Insurance requires a four-point inspection (electrical, plumbing, HVAC and roof) for mobile home applications on homes more than 20 years old. If you are adding shutters to an older home, have the inspection done and fix any hazards first.
IBHS's FORTIFIED program lists "manufactured homes built after 1994 (HUD wind zone rated)" among homes that qualify for a designation. If you are re-roofing a newer manufactured home anyway, ask a FORTIFIED evaluator whether it is worth pursuing. See FORTIFIED and opening protection.
Keep the paperwork: data plate photo, installer license and installation decal information, tie-down inspection, shutter product approval and any permit. Take photos of the home with shutters closed before you evacuate. They help with a claim. See after the storm: claims and repairs.
How to choose a provider
- Photograph the data plate and confirm the home's HUD wind zone matches your county.
- Have tie-downs and anchoring inspected by a licensed installer and ask your Florida insurer about the tie-down discount.
- Ask the park office for its rules on exterior changes before ordering permanent shutters.
- Choose shutters or screens whose product approval lists a substrate and anchor that match your wall.
- Make sure every fastener goes into framing, never siding alone.
- Ask your building department whether a permit is needed and who may pull it.
- If using plywood, pre-cut, label and pre-drill panels and install permanent anchors in framing now.
- Secure skirting, carports, sheds and loose items.
- Know your evacuation zone and destination, close the shutters, and leave when officials call for mobile home residents to evacuate.
Related hurricane shutters and impact windows guides
- What Are the Types of Hurricane Shutters? Accordion, Roll-Down, Panels, Fabric, Colonial and Bahama Compared
- Do Fabric Hurricane Screens and Storm Curtains Really Work?
- Which Hurricane Storm Panels Are Best: Steel, Aluminum or Clear Polycarbonate?
- Can You Use Plywood for Hurricane Shutters? Code Rules, Thickness, Fasteners and Where Plywood Is Not Allowed
- Landlords and Tenants: Who Has to Install and Put Up Hurricane Shutters on a Rental in Florida and Texas, and Who Pays?
- Does My Safe Florida Home Pay for Impact Windows and Doors? 2026 Eligibility, Match and Status
- IBHS FORTIFIED Home and Opening Protection: What Silver and Gold Require for Windows, Doors and Garage Doors in Florida and Texas
Hurricane shutters and impact windows by state and city
Questions people ask
Can you put hurricane shutters on a mobile home?
Yes, in most cases. Fabric screens, panels and accordion shutters are common on manufactured homes. The fasteners must go into wall framing, not just siding, and the installation should match the product approval's listed substrate and anchors. Shutters protect windows and the inside of the home, but they do not keep the home from moving, so tie-downs matter more, and you still need to evacuate.
What HUD wind zone is my county in?
In Florida, Broward, Charlotte, Collier, Miami-Dade, Franklin, Gulf, Hendry, Lee, Martin, Manatee, Monroe, Palm Beach, Pinellas and Sarasota are Zone III, and every other county is Zone II. In Texas, 15 coastal counties from Orange to Cameron are Zone II and every other county, including Harris, is Zone I. Your home's data plate shows the zone it was built for.
Is it safe to stay in a mobile home with shutters during a hurricane?
No. Florida's Division of Emergency Management says people in mobile homes should follow all evacuation orders, and the National Weather Service says a mobile home is not a safe shelter from tornadoes, which hurricanes can produce. Shutters protect windows, not the structure. Close them, secure the home, and evacuate.
Are mobile homes eligible for My Safe Florida Home?
No. Section 215.5586 requires the home to be site-built, owner-occupied and homesteaded for an MSFH inspection, and grants require inspection eligibility. Manufactured and mobile homes are not site-built. The 2026 rewrite of the program kept that requirement in the statute text we reviewed.
Do I need a license to install shutters on my mobile home in Florida?
A state mobile home installer license under s. 320.8249 covers setting up and anchoring the home. Shutters are hurricane protection devices, which Florida's specialty structure contractor category covers, along with general, building and residential contractors within their scopes. Ask your local building department whether a permit is required and whether you may pull an owner permit for your situation.
Can I put a Zone I manufactured home on the Texas coast?
Not a newer one. Texas Occupations Code s. 1201.256 says a manufactured home built on or after September 1, 1997 must meet HUD Wind Zone II standards to be installed in a Zone II county, which covers 15 coastal counties. Homes built before that date may be installed without that restriction, but they were not designed for coastal hurricane winds.
How much do hurricane shutters cost for a mobile home?
We could not find a named, dated cost study for shutters on manufactured homes in Florida or Texas, so we do not quote a price. Costs depend on the number and size of openings, the shutter type, and how much framing work is needed to anchor them. Get at least two written quotes that list each opening, the product approval and the anchor type.
Sources
- 24 CFR 3280.305, structural design requirements (wind zones), eCFR
- Texas Occupations Code Chapter 1201, manufactured housing
- Florida Statutes s. 320.8325, mobile home installation standards
- Florida Statutes s. 320.8249, mobile home installers license
- Florida Statutes s. 627.0629, rate filings and mitigation discounts
- Florida Statutes s. 627.351, Citizens eligibility
- Florida Statutes s. 215.5586, My Safe Florida Home
- Laws of Florida ch. 2026-174
- My Safe Florida Home
- Florida Statutes s. 723.035, mobile home park rules
- Florida Statutes s. 83.51, landlord's obligation to maintain premises
- Florida rule 61G4-15.015, specialty structure contractor
- Florida Statutes s. 553.73, Florida Building Code (manufactured buildings)
- Florida Building Code 2023, Chapter 16 Structural Design
- Florida Division of Emergency Management: Know Your Zone
- National Weather Service: Tornado safety, during
- National Weather Service Corpus Christi: Hurricane Harvey
- Florida Climate Center (FSU): Hurricanes
- Citizens Property Insurance: inspections
- FORTIFIED Frequently Asked Questions (IBHS)
- Understanding Wind Risks: Common Myths (FORTIFIED/IBHS)
- TDI Windstorm: protecting openings FAQ
This guide was written by our editorial team from the public sources listed above. It is general information, not legal advice; confirm licensing and terms directly with any provider.


