New ebook: Before You Borrow, how lenders decide and how to get your business loan approved. Get it for $7.99 →
New ebookHow to Research Like a Wall Street AnalystFind original sources, analyze trends, build your own insightsGet it now →
Markets
Real businesses. Bigger perspective. · Thu, Nov 19, 2026News. Tools. Scores. Games. Free.The Morning Chronicle
Donate BTCOpen dDashboard

Local Guide · Plumbing

What Plumbing Maintenance Should I Do, and When? A Month-by-Month Calendar for Texas and Florida Homes

A state-by-state plumbing calendar: what to check monthly, how to prep for Texas freezes and Florida hurricane season, which tasks are yearly, and a printable checklist.

Check under sinks, the water heater pan and toilets monthly. Each year, exercise every shut-off valve, inspect supply lines, dye-test toilet flappers (replace them at least every five years, per EPA) and service the water heater per its manual. In Texas, prep pipes for freezes each fall. In Florida, test shut-offs, backwater valves and pump alarms before hurricane season starts June 1. Schedule required backflow tests and septic service.

Key facts

  • EPA advises checking toilet flappers and replacing them at least every five years.
  • Household leaks waste more than 9,300 gallons a year on average, according to EPA.
  • EPA says septic systems should be inspected at least every three years and tanks typically pumped every three to five years.
  • Texas requires backflow assemblies that protect against health hazards to be tested at least yearly (30 TAC 290.44).
  • Florida requires residential backflow assemblies to be tested at least every two years and non-residential ones yearly (Rule 62-555.360).
  • The Atlantic hurricane season runs June 1 to November 30, per the National Weather Service.
  • The Red Cross advises keeping heat at 55F or higher when away during freezing weather.
  • Florida automatic irrigation systems must have working rain shutoff technology (Statute 373.62).
  • Manufacturer manuals we reviewed recommend testing the T&P relief valve and flushing the tank every six months.

Start here: the new-homeowner plumbing walk-through

Do this once, the first weekend you own the house or move into a rental. It takes about an hour and it is the most useful plumbing maintenance you will ever do, because in an emergency you will already know where everything is.

Find and label every shut-off

  • House main. In most Texas and Florida slab homes it is where the supply line enters the house: in the garage, near the water heater, on an outside wall facing the street, or in a utility closet. Turn it off and back on to make sure it works. Tag it with a bright label.
  • Meter valve. In the meter box near the street. Austin Water notes the owner's shut-off is typically on the owner's side of the meter box. Keep a meter key in the garage.
  • Fixture valves. Under every sink, behind every toilet, behind the washer, at the fridge ice-maker line and at the dishwasher (usually under the kitchen sink).
  • Water heater. The cold-water inlet valve on top, plus the gas valve or the breaker.
  • Irrigation and pool. The sprinkler system's own shut-off and backflow device, and pool equipment valves.
  • Gas. The meter shut-off and appliance valves. Know how to leave and who to call if you smell gas. See gas leak steps.

Find the cleanouts

A sewer cleanout is a capped pipe, often 3 or 4 inches, usually outside near the foundation or near the property line. Inside, there may be cleanouts in a garage wall or under a sink. Clear plants away from outdoor cleanouts so a plumber can reach them fast. See main sewer line clogs.

Record your baseline

  • Water heater: brand, model, size, fuel, install date (often on the label or permit sticker)
  • Pipe types you can see: at the water heater, under sinks and at the main. See pipe identification.
  • Water pressure at a hose bib, using an inexpensive screw-on gauge. See water pressure.
  • A meter reading taken before bed and again in the morning with no water used. Any change means a leak. See leak detection.
  • Whether you are on sewer or septic, and if septic, the last pump-out date. See septic vs sewer.
  • Whether you have a grinder or lift-station pump and its alarm panel. See grinder and ejector pumps.

Monthly plumbing checks (10 minutes)

  • Look under every sink with a flashlight. Feel the cabinet floor for soft or swollen spots. Catching a slow drip here prevents most cabinet mold. See under-sink leaks.
  • Check the water heater pan and the floor around it for water or rust.
  • Glance at toilets for running water or a wobble at the base. See toilet problems.
  • Run water in unused drains (guest baths, floor drains) to keep traps full so sewer gas stays out. See sewer smells.
  • Watch the water bill. A jump without a reason is often the first sign of a hidden leak. See high water bills.
  • Florida and humid Gulf Coast homes: check the A/C condensate drain line is flowing and the air handler pan is dry.
  • Grinder pump homes: make sure the alarm panel light is off and the lid is clear.

Seasonal calendar for Texas

SeasonTasks
Spring (March to May)Do a full leak check during EPA's Fix a Leak Week in March (March 16 to 22 in 2026). Turn on and inspect irrigation after winter: broken heads, leaks, rain or freeze sensor. Reset the controller to your city's watering days. Check outdoor hose bibs for freeze damage.
Summer (June to August)Watch for slab-leak signs as clay soil dries and shifts: warm floors, new cracks, a moving meter. Check the attic water heater pan and drain line. Gulf Coast homes: before peak hurricane months, test the main shut-off and any backwater valve.
Fall (September to November)Freeze prep: insulate pipes in attics, garages and exterior walls; buy hose-bib covers; label shut-offs; drain and winterize irrigation where needed. Flush the water heater if your manual calls for it.
Winter (December to February)On freeze nights: disconnect hoses, cover hose bibs, drip faucets fed by exposed pipes, open sink cabinets on outside walls, and keep the heat steady. If you leave town, Austin Water suggests shutting water at the meter and keeping the thermostat at 65F or higher.

Texas freeze prep in detail

Winter Storm Uri in February 2021 drove Houston to 13F and College Station to 5F, according to the National Weather Service, and broken pipes were everywhere. The Red Cross lists the highest-risk pipes as outdoor hose bibs, pool and sprinkler lines, and pipes in unheated attics, garages, crawl spaces, cabinets and exterior walls. Its advice: let cold water drip from faucets served by exposed pipes, keep the thermostat the same day and night, and keep heat at 55F or higher when away. If a pipe freezes, Austin Water says to shut off the water first, open a nearby faucet, warm the pipe gently from the faucet back toward the wall, and check for cracks once water flows. Never use an open flame. See frozen pipes in Texas.

Seasonal calendar for Florida

SeasonTasks
Spring (March to May)Fix a Leak Week check in March. Test the irrigation rain sensor or smart controller, which Florida Statute 373.62 requires on automatic systems. Confirm your watering days with your water management district or city, since dry-season restrictions often tighten.
Before June 1Hurricane season runs June 1 to November 30, per the National Weather Service. Test the main shut-off, the backwater valve if you have one, and the grinder or lift-station alarm. Learn how long your pump can hold wastewater without power. Store bottled water.
Summer (June to September)Watch indoor humidity and check under sinks and at the air handler for mold. Check pool equipment for leaks. After every big storm, look for sewer smells or slow drains.
Fall (October to November)Flush the water heater if your manual calls for it. Before your insurance renewal, gather your water heater age and any plumbing updates for a 4-point inspection if your carrier needs one. See 4-point inspections.
Winter (December to February)North Florida and the Panhandle can freeze. Jacksonville and inland homes should cover hose bibs and protect exposed pipes on cold nights.

After a hurricane or flood

  • Do not drink well water after flooding until it is tested. See well water.
  • Have a septic system checked before heavy use if the drain field was under water.
  • Limit water use if the power is out and you have a grinder pump.
  • Hire only licensed contractors. Florida makes unlicensed contracting during a declared state of emergency a third-degree felony (Statute 489.127).

Full storm guide: hurricane and flood plumbing.

Annual and multi-year tasks

TaskHow oftenSource or reason
Test the house main and fixture valvesYearlyValves that never move seize; you need them in an emergency
Check toilet flappers with dyeYearly; replace at least every 5 yearsEPA WaterSense
Inspect washer, toilet, sink and ice-maker supply linesYearly; replace any that are bulging, kinked, rusted or crackedTDI cites a broken washer hose as a typical sudden water loss
Test the water heater T&P relief valvePer your manual; some manufacturer manuals say every 6 monthsA. O. Smith and American Water Heater manuals
Drain and flush the water heaterPer your manual; some say every 6 months, more often with hard waterA. O. Smith and American Water Heater manuals
Check the water heater anode rodPer your manual; one manufacturer says after at most 3 years, then yearly, and yearly if you use a softenerA. O. Smith and American Water Heater manuals
Backflow assembly testTexas: yearly for health-hazard assemblies; Florida: yearly at non-residential and every 2 years at residential connections30 TAC 290.44; Rule 62-555.360
Septic inspectionAt least every 3 years; yearly for systems with pumps or floatsEPA
Septic pump-outTypically every 3 to 5 yearsEPA; Miami-Dade advises 3 to 5 years with a permitted hauler
Sewer camera inspectionWhen buying, after repeated clogs, or every few years on older cast iron or clay linesFinds roots and breaks before backups
Check water pressureYearlyHigh pressure strains fixtures and heaters
Test leak sensors and shut-off devicesYearly; replace batteriesManufacturer instructions

Manufacturers set the water heater intervals, and they vary by model. The six-month and anode intervals above come from commercial water heater manuals we reviewed; your home unit's manual is the authority. See water heater maintenance.

Warning signs that should not wait for the calendar

A calendar catches slow problems. These signs mean act now, not at the next scheduled check:

SignLikely causeWhat to do
Water meter moves with everything offHidden leak, possibly under the slabClose the house main; if the meter stops, the leak is inside. Call a plumber for leak detection. See slab leaks.
Several drains back up at onceMain sewer line blockageStop all water use and call a plumber. See sewer backup.
Rotten-egg smell near gas appliancesGas leakLeave and call the gas utility from outside. See gas leak steps.
Water in the heater pan or rust at the baseTank or fitting failingClose the cold inlet, shut off gas or power. See water heater leaking.
T&P valve drippingHigh pressure or thermal expansionCheck pressure and the expansion tank. A. O. Smith says excessive pressure is the most common cause.
Banging pipes when valves closeWater hammer or high pressureSee noisy pipes.
Musty smell or a soft cabinet floorSlow leak and possible moldFind and stop the leak, then dry within 24 to 48 hours. See mold after a leak.
Grinder pump alarm stays onPump failure or blockageStop using water and call the number on the panel.

If water is damaging the house, report it to your insurer quickly and photograph everything before cleanup. See the claim process.

How often should I replace supply lines and flappers?

Flappers: EPA's WaterSense program says to check toilet flappers and replace them at least every five years. A leaking flapper can waste hundreds of gallons a day without making much noise. Test with a few drops of food coloring in the tank; if color shows up in the bowl within about 15 minutes without flushing, replace the flapper.

Supply lines: No state law sets a schedule. Check them yearly and replace any rubber washing machine hoses with braided stainless steel. Replace any line that is bulging, kinked, corroded at the nut or older than the maker's stated life. Write the date on a piece of tape on the new line. Braided toilet and faucet connectors are cheap compared with a water claim.

When should I flush my water heater in hard water areas?

Follow your heater's manual. Manufacturer manuals we reviewed from A. O. Smith and American Water Heater recommend draining and flushing the tank every six months to reduce sediment buildup. With hard water, which is common in much of Texas and Florida, sediment builds faster and you may hear rumbling or popping. That sound means scale is insulating the bottom of the tank.

The same manuals note that artificially softened water is more corrosive and calls for checking the anode rod yearly. If you have a tankless heater, the maker's manual usually calls for periodic descaling with a pump kit. See hard water and softeners and tank, tankless and heat pump heaters.

A word of caution: on an old tank that has never been flushed, opening the drain valve can stir up sediment that keeps the valve from closing fully. Have a hose cap ready, or ask a plumber to do the first flush.

What should I do before leaving home for a month?

  1. Shut off the main. This is the single best protection. If you have a fire sprinkler system fed from the same line, ask a plumber first.
  2. Water heater. Set it to "vacation" mode or turn it off. If you shut off the main, also turn off an electric heater's breaker so elements do not burn out if the tank drains.
  3. Irrigation. If the irrigation runs off the same supply, leave the controller on only if you leave the water on.
  4. Climate. In summer, keep the A/C running at a moderate setting to control humidity and mold. In a Texas winter, keep the heat on; Austin Water suggests 65F or higher if you leave town.
  5. Grinder pump. E/One, a grinder pump maker, advises running clean water into the unit until the pump turns on, then letting it pump down before you leave.
  6. Insurance. Check your policy's vacancy terms. TDI notes common exclusions include freezing pipes while the house is unoccupied and losses after the home is vacant for the number of days the policy sets.
  7. Someone to check. Ask a neighbor to look in weekly, especially after storms or freezes.

Printable plumbing maintenance checklist

Print this list and tape it inside a utility closet.

Once

  • Locate and label house main, meter valve, fixture valves, water heater valve, irrigation shut-off, gas shut-off
  • Locate sewer cleanouts and septic or grinder pump lids
  • Record water heater age, pipe types and baseline pressure

Monthly

  • Under sinks, water heater pan, toilets, unused drains, water bill
  • A/C condensate line (Florida and Gulf Coast)

Spring

  • Fix a Leak Week meter test and dye test
  • Irrigation check and rain sensor test; confirm watering days

Before June 1 (Florida and Gulf Coast)

  • Test main shut-off, backwater valve, pump alarms; plan for outages

Fall

  • Texas freeze prep: insulation, hose-bib covers, labels
  • Water heater flush and T&P test per manual

Yearly

  • Exercise all valves; check supply lines; check pressure
  • Backflow test if your utility requires it
  • Septic inspection on schedule

Landlords and property managers can use the expanded version in the landlord plumbing checklist.

How to choose a provider

  • Locate, test and label the house main and meter valve.
  • Locate fixture valves, the water heater valve, irrigation and gas shut-offs.
  • Find sewer cleanouts and clear plants around them.
  • Record water heater age, pipe types and water pressure.
  • Check under sinks and the water heater pan every month.
  • Dye-test toilets and replace flappers at least every five years.
  • Inspect supply lines yearly and swap rubber washer hoses for braided ones.
  • Service the water heater on the schedule in its manual.
  • Texas: insulate pipes and cover hose bibs each fall.
  • Florida: test shut-offs, backwater valves and pump alarms before June 1.
  • Schedule required backflow tests and septic service.
  • Before a long trip, shut off the main and set the water heater to vacation.

Related plumbing guides

Plumbing by state and city

Questions people ask

What plumbing maintenance should I do every year?

Exercise the main shut-off and fixture valves, check every supply line, test toilet flappers with dye, check water pressure with a gauge, and service the water heater as its manual says. If your utility requires it, schedule your backflow test: yearly for Texas health-hazard assemblies, and every two years at Florida residential connections. Septic owners should follow EPA's inspection schedule.

How often should septic be pumped?

EPA says household septic tanks are typically pumped every three to five years and inspected at least every three years. Alternative systems with pumps or floats generally need yearly inspection. Miami-Dade advises a three-to-five-year schedule using a permitted liquid waste transporter. Tank size, household size and garbage disposal use change how fast solids build up.

When should I test my backflow preventer?

Your water utility will tell you, but the state rules set the floor. In Texas, 30 TAC 290.44 requires assemblies protecting against health hazards to be tested at least yearly by a licensed tester. In Florida, Rule 62-555.360 requires testing at least yearly at non-residential connections and at least every two years at residential connections.

How often should I check under sinks for leaks?

Monthly is a good habit and takes a minute per sink. Use a flashlight, look at the trap and supply connections, and press on the cabinet floor for soft spots. A small leak caught early is a cheap fix; one found after months often means cabinet replacement and mold cleanup.

Do I need a plumber for yearly maintenance?

Most monthly and yearly checks are do-it-yourself tasks. Use a licensed plumber for gas water heater service, a stuck main valve, backflow testing (which needs a licensed tester), sewer camera inspections and anything that means opening a wall. In Texas, check the license on the TSBPE lookup; in Florida, use DBPR's search.

Should I install a whole-house leak shut-off valve?

For many homes it is worth considering, especially with attic water heaters or second-floor laundry. These devices close the main when they sense a leak or unusual flow. Some insurers offer discounts, so ask yours. Installation on the main usually needs a plumber and may need a permit in some cities.

What should I do before a hard freeze in Texas?

Disconnect hoses, cover hose bibs, insulate exposed pipes, open sink cabinets on outside walls, let faucets fed by exposed pipes drip, and keep heat steady day and night. Know where your main shut-off is in case a pipe bursts. If you are leaving, Austin Water suggests shutting water at the meter and keeping the thermostat at 65F or higher.

Sources

This guide was written by our editorial team from the public sources listed above. It is general information, not legal advice; confirm licensing and terms directly with any provider.

New ebook from The Company ChronicleHow to Research Like a Wall Street AnalystFind original sources, analyze trends, and build your own insights. 36 pages with worksheets.Get the ebook · $29Instant PDF download

Business Spotlight

Want us to publish your business?

Our team writes and publishes articles about your business on The Company Chronicle every month, with a link to your website. Plans from $30 a month, cancel anytime.

Publish with us

The Chronicle directory

What are you into?

The Chronicle, coast to coast

Every corner has a story.

The full Chronicle illustration