Local Guide · Hurricane shutters and impact windows
Impact Sliding Glass Doors: Why Do They Leak in Hurricanes, What Design Pressure Do You Need, and What Do They Cost?
Why a slider can survive a hurricane structurally and still let water in, what the 15% water test rule means, sill and track options, large-opening engineering, condo rules, shutter alternatives and cost drivers in Florida and Texas.
Impact sliding glass doors resist debris and wind pressure, but their water rating is separate and much lower. Florida's TAS 202 and the national fenestration standard test water resistance at about 15% of the positive design pressure, and a 2024 Florida Building Commission review found that may not reflect real hurricane rain. To limit leaks, choose a door with a high water rating and a high-performance sill, keep the tracks and weep holes clear, and consider a shutter in severe exposures.
Key facts
- TAS 202 water testing applies a static air pressure of at least 15% of the product's positive design pressure for 15 minutes while spraying 5 gallons per hour per square foot, about 8.02 inches of rain per hour (FIU report for the Florida Building Commission, Nov. 2024).
- Under NAFS-22, water test pressure is at least 15% of the positive design pressure for classes R, LC and CW and 20% for class AW, never below about 2.92 psf and capped at about 15.04 psf.
- NAFS-22 allows sliding doors and some other door types to be rated 'Limited Water' and report a water test pressure as low as 0 psf.
- A product with Performance Grade 60 must pass water testing at 9 psf, which is 15% of its positive rating.
- FEMA's Hurricane Ian assessment (P-2342, 2023) found water intrusion primarily through sliding glass doors and soffits, including in homes built in 2021 with overhangs, and found some sliders lacked adequate sill risers.
- In wind tunnel tests reviewed for the Florida Building Commission, shutters over a slider cut net pressure by 34% and water intrusion by 75%.
- The Florida Building Commission review says aftermarket water-intrusion devices for sliders must go through the Florida product approval system.
- FBC 1709.5 limits alternate-size sliding door ratings: the panel area may not exceed the panel area of the tested unit.
Why do sliding glass doors leak during hurricanes?
Because surviving a hurricane and keeping water out are two different tests, and sliders are built in a way that makes water the harder one.
- Sliding panels cannot be clamped shut. A slider's panels ride on rollers in a track and seal with weatherstripping and interlocks. There is always a path at the sill, at the interlock where panels meet, and at the track ends.
- Wind pushes water uphill. In a hurricane, pressure on the outside face of the door is higher than inside. That difference drives water over the sill and through the seals, and gusts can make panels vibrate or deflect.
- The water test is gentler than the storm. Florida's TAS 202 water test applies at least 15% of the door's positive design pressure for 15 minutes while spraying 5 gallons of water per hour per square foot, about 8.02 inches of rain per hour. The national standard (NAFS) uses 15% for most residential classes and 20% for the heaviest class, capped at about 15 psf. A door rated for a structural pressure of 60 psf may therefore be water-tested at only 9 psf.
- "Limited Water" sliders exist. NAFS-22 lets sliding doors be rated as Limited Water and report a water test pressure as low as zero.
In 2024 the Florida Legislature (Section 32 of HB 1021) told the Florida Building Commission to study water intrusion through the tracks of sliding glass doors. The resulting November 2024 report by Florida International University researchers found that the typical 15% design pressure water protocols in TAS 202 and NAFS may not adequately assess rain intrusion, which was "much lower than what an SGD might face during actual hurricanes." FEMA's assessment teams reached a similar conclusion after Hurricane Michael (2018) and Hurricane Ian (2022). After Ian, FEMA observed water intrusion primarily through sliding glass doors and soffits, including in homes built in 2021 with protective overhangs, and found some sliders lacked adequate sill risers.
Water resistance vs. design pressure: two different numbers
| Rating | What it tells you | Typical relationship |
|---|---|---|
| Design pressure (DP) | Structural strength: the pressure the door resists without failing, positive and negative | Tested to 1.5 times DP for structural safety |
| Performance Grade (PG) | The NAFS rating that combines structural and water performance | Water test at 15% or 20% of the PG pressure |
| Water test pressure | The pressure at which no water got through during the test | Often listed separately; may be higher than 15% if the maker tested it higher (a NAFS "secondary designator") |
| Impact rating | Debris resistance (large or small missile) plus cyclic pressure | Unrelated to water |
The FIU report explains that NAFS allows a secondary designator on the label when the water performance exceeds the minimum, and that manufacturers can use it to offer products that meet more rigorous water requirements. FEMA's Ian report went further and recommended that the national standard require water performance ratings equal to the positive design pressure. That is not the rule today.
What to do with this: when comparing sliders, ask for the water test pressure, not just the DP. A slider with the same DP but a much higher water test pressure is the better choice for an exposed wall. See design pressure ratings explained.
Sill risers and high-performance sills
The sill is where most slider water enters. Options that help:
- Taller sill or sill riser. A higher interior sill leg gives water more height to climb before it reaches the floor. FEMA's Ian report noted sliders lacking adequate sill risers. Ask whether the door's approval includes a high-performance or raised sill option, and whether your floor and threshold allow it.
- Drainage. Sills drain water back out through weep holes. FEMA's photos from Ian show weep holes that allow water to leave. Blocked weeps turn the track into a pool that overflows inward.
- Sill pan and flashing. A pan under the sill, integrated with the wall's water barrier, catches water that gets past the door and sends it outside. FEMA points installers to ASTM E2112, the installation practice aimed at minimizing water infiltration.
- Accessibility trade-off. Low or flush thresholds are easier to walk over but make water control harder. FEMA says avoiding water infiltration in strong hurricanes is especially challenging where low thresholds are needed for accessibility.
- Aftermarket devices. The Florida Building Commission report says aftermarket devices sold to reduce water intrusion through slider tracks need to go through the Florida product approval system to be considered, with a building official able to approve testing under FBC 104.11. Do not drill into an approved door's frame to add one without confirming the device is approved for that door.
What design pressure do you need for a sliding door near the beach?
There is no single number. Design pressure is calculated for each opening from the site's design wind speed, the exposure category, the building height, the opening's location on the wall (corners get higher suction) and the door's size. Your installer, designer or building department determines it.
- Exposure D. Exposure D applies to flat, unobstructed areas and water surfaces, and produces the highest pressures for a given wind speed. A beachfront home in Galveston, Port Aransas, Miami Beach or Clearwater Beach facing open water may be Exposure D.
- HVHZ. In Miami-Dade and Broward, every building is designed as at least Exposure C (FBC 1620.3), with Risk Category II design wind speeds of 175 mph in Miami-Dade and 170 mph in Broward.
- Texas coast. Since April 1, 2026, TDI requires windstorm work to be certified to the 2024 IRC or IBC and says the wind speed must be determined for each structure, for example with the ASCE 7 Hazard Tool. Most of the designated catastrophe areas are now in the wind-borne debris region.
- Height. Upper-floor sliders see higher pressures. In the HVHZ, glazing above 30 feet must still pass the small missile test, with no 60-foot exemption.
Miami-Dade's permit checklist requires plans to show the required positive and negative design pressures for each window or door. Make sure the slider's approved rating, for your exact size and panel configuration, meets both numbers.
Large openings, multi-slide and pocket doors
Multi-panel and pocket sliders are available with impact approvals; Miami-Dade's product search has a "Sliding" subcategory for doors. Large openings bring extra engineering:
- Size limits come from testing. The label must show the maximum size tested (FBC 1709.5.1). Ratings for other sizes are allowed by engineering analysis, but for sliding and bi-fold doors the panel area of the alternate size may not exceed the panel area of the tested unit, and it may not exceed the tested unit's air and water resistance or cyclic pressure.
- The header and structure. Wide openings need a header and framing that carry the door's wind load into the building. Mullions, where used, must be tested or engineered and limited to deflection of L/175 for spans up to 13 feet 6 inches (FBC 1709.8.2).
- Glass weight. Large impact panels are heavy, which affects rollers, track and how easily the door slides.
- The largest available size varies by product line and changes as manufacturers add tested sizes; check each approval's size tables rather than relying on a sales claim.
Resizing an opening is new construction work: it needs a permit and usually sealed drawings, unlike a same-size replacement (FBC 107.1.1).
Should you shutter a sliding door instead?
You can. The code accepts a non-impact slider protected by an approved shutter, and accordions and roll-downs are common choices for sliders because they close quickly. Two research findings are worth knowing:
- FEMA's 2018 recovery advisory says shutters placed over windows should not be relied on to protect against wind-driven rain, and that a shuttered unit must still meet its design pressures.
- Newer wind tunnel tests reviewed in the 2024 Florida Building Commission report found shutters did reduce water intrusion: on a sliding door, shutters lowered net pressures, and a 34% pressure reduction cut water intrusion by 75%. Accordion shutters generally performed better than aluminum storm panels in that study, which the authors said shows the importance of installation.
Practical reading: a shutter helps with water as well as debris, but do not count on it to make a leaky slider dry. For an exposed slider, an impact door with a good water rating plus a shutter for major storms gives the most protection. Remember that a shuttered slider is not an exit. Cost comparison: Fixr's 2025 guide puts shutters for sliding glass doors at $12 to $60 per square foot installed. See hurricane shutter costs and roll-down shutters.
Can an existing slider be reinforced instead of replaced?
Not into an impact-rated door. An impact rating belongs to a tested assembly. There is no approved way to add impact resistance to an existing non-impact slider by changing its glass or adding braces, unless the resulting combination has its own approval. Your realistic options are:
- Replace the slider with an approved impact unit
- Keep the slider and protect it with an approved shutter
- Improve water control with approved sill devices, new weatherstripping, roller and track service, and better drainage
Replacing broken glass in an impact slider must use the glass type in that door's approval. In Texas, TDI lists glass replacement in doors among projects that do not need a windstorm inspection.
Fixing a hard-to-slide impact door: rollers and tracks
Impact panels are heavy, so rollers and tracks wear. A door that is hard to slide is also more likely to leak, because worn rollers let a panel sit low and misalign its seals. Basic care:
- Vacuum and wipe the track often; sand and grit grind rollers.
- Clear the weep holes with a soft wire or a blast of air so water drains out.
- Follow the manufacturer's instructions on cleaning and lubrication; some tracks should not be oiled.
- Have worn rollers replaced with the manufacturer's parts and the panel height adjusted so interlocks and weatherstripping meet properly.
- Check weatherstripping and interlock seals each spring before hurricane season.
- Near salt water, rinse frames and hardware to slow corrosion.
Florida's 2026 wind mitigation form says all openings must be in good condition. A slider that is damaged and needs repair or replacement is marked Z, and the home does not qualify for mitigation rate differentials. See maintenance.
Condos and high-rise balconies
Balcony sliders are the most common replacement in Florida condos, and the rules are tighter:
- Association specs and approval. Florida Statutes 718.113(5) requires the board to adopt hurricane protection specifications; it may not refuse an installation that conforms to them but may require a unified exterior look. Get approval before ordering.
- Permit. Yes, a permit is required for replacement in a condo, and since January 26, 2026, window and door installations in threshold buildings (more than three stories or 50 feet) need a threshold inspection by a state-certified Special Inspector plus a special inspection plan from the engineer of record. Miami-Dade now asks for wind calculations for all openings, wood buck calculations where bucks are 1-1/2 inches or thicker, a Threshold Building Affidavit and a Special Inspector form.
- Height. Outside the HVHZ, glass more than 60 feet up may be exempt from impact protection in some conditions (FBC 1609.1.2). In the HVHZ, there is no such exemption; sliders above 30 feet must pass the small missile test.
- Removal for association repairs. Unless the declaration says otherwise, owners are not responsible for the cost of removing and reinstalling windows and doors when the association needs them removed for its maintenance or repairs (718.113(5)(d), as amended by ch. 2025-175).
See high-rise condo window replacement projects and condo hurricane protection under 718.113.
How much does an impact sliding glass door cost?
We found no reliable, dated cost study specific to impact sliding doors in Florida or Texas. Today's Homeowner's 2025 hurricane window guide lists a sliding glass door unit at about $2,800, a single national figure that does not reflect multi-panel, pocket or high-design-pressure doors, which cost much more. Cost drivers:
- Width, height and number of panels
- Design pressure and exposure
- Water rating and high-performance sill options
- Glass: laminated, insulated laminated, Low-E, tint
- Frame: aluminum or vinyl, thermal break, color
- Opening changes, header work, stucco and floor repair
- Condo engineering and threshold inspections
- Permit: unincorporated Miami-Dade charges $150.82 for a single-family window or door installation permit (October 2026 schedule)
Florida's My Safe Florida Home grants can cover exterior doors and windows as opening protection when the program's inspection recommends them; the portal has been offline since November 10, 2026. In the Texas catastrophe area, plan for a WPI-8 windstorm certificate. See impact window costs.
Texas coast: sliders and windstorm certification
For homes in the TDI catastrophe area, including Galveston, Port Aransas, Corpus Christi, Rockport, South Padre Island and the Harris County cities east of State Highway 146, replacing a sliding glass door is window and door work that needs a windstorm inspection and Certificate of Compliance (WPI-8) for the home to stay eligible for TWIA coverage. File Form WPI-1 with TDI before the work starts; TDI inspectors charge no fee but must see the work during installation. A Texas-licensed engineer can certify completed work instead (WPI-8-E), which TDI says can be more invasive and more expensive.
TDI tells homeowners to use opening protection tested to ASTM E1886 and E1996 and designated by a recognized product approval, and since April 1, 2026, work is certified to the 2024 IRC or IBC with the wind speed set for each structure. Beachfront sites facing the Gulf may fall in Exposure D, so ask your engineer or installer to confirm the slider's design pressure for your site before ordering. See TWIA windstorm certification.
Are impact sliders good for security?
Laminated impact glass stays in the frame when broken, which makes forced entry through the glass slower and noisier than through ordinary tempered glass. Many door approvals include forced entry testing under TAS 202. The weak points of any slider are the lock and the ability to lift a panel off its track, so check the locking hardware and anti-lift features. See security benefits of impact windows and doors.
How to choose a provider
- Ask for the slider's water test pressure, not just its design pressure.
- Ask whether a high-performance or raised sill is available and approved for the door.
- Confirm the design pressure for your exact size and panel configuration meets both required values.
- Check the approval's maximum tested size and panel area.
- Make sure the installer uses a sill pan and flashing integrated with the wall.
- In a condo, get association approval and plan for threshold inspections if the building is over three stories or 50 feet.
- Keep tracks and weep holes clean and service rollers before each season.
- Consider a shutter for exposed sliders in major storms, and plan another exit.
- Do not add aftermarket sill devices unless they hold Florida product approval for your door.
- In Texas coastal counties, file WPI-1 and get the WPI-8 before final payment.
Related hurricane shutters and impact windows guides
- Impact Entry Doors and French Doors: What Are the Ratings, Costs and Rules, and What Should You Look For?
- How Much Do Impact Windows Cost in Florida and Texas? Per Window, Per House and What Drives the Price
- Design Pressure (DP) Ratings Explained: What Do DP50 and +60/-70 psf Mean for Your Windows?
- How Do Condo Buildings Replace All Their Windows? Engineering, SIRS, Votes, Access and Costs in Florida and Texas
- Are Roll-Down Hurricane Shutters Worth It? Motorized vs. Manual, Battery Backup and Power Outages
- What Should You Do After a Hurricane Breaks Your Windows or Damages Your Shutters? Claims, Repairs and Code Upgrades
- What Are Impact Windows and How Do They Survive a Hurricane? Laminated Glass, Frames and Ratings Explained
Hurricane shutters and impact windows by state and city
Questions people ask
Why did my brand-new impact slider leak during the storm?
Because its water rating is much lower than its structural rating. Water tests are typically run at about 15% of the positive design pressure, and a 2024 review for the Florida Building Commission found that this may not reflect real hurricane rain. FEMA observed slider leaks in homes built as recently as 2021. Check installation, sill flashing and weep holes, and ask the installer and manufacturer to inspect.
What sill height helps prevent water intrusion?
We found no code-set sill height for sliders. A taller interior sill leg or riser generally gives more resistance to water being pushed over the sill, and FEMA noted sliders lacking adequate sill risers after Hurricane Ian. Ask for the door's high-performance sill option and its water test pressure, and weigh it against accessibility, since low thresholds make water control harder.
Do I need a permit to replace a condo sliding door?
Yes, in Florida a replacement slider needs a building permit, and the association must approve it under its hurricane protection specifications. Since January 26, 2026, window and door installations in threshold buildings, those more than three stories or 50 feet tall, also need a threshold inspection by a state-certified Special Inspector and a special inspection plan.
Are multi-slide pocket doors available in impact versions?
Yes, many manufacturers offer multi-panel and pocket configurations with impact approvals. Check the approval for the exact configuration, panel sizes and design pressure. Under FBC 1709.5, ratings for alternate sizes are allowed only within limits, including that the panel area may not exceed the tested panel area.
Will an impact slider earn an insurance discount by itself?
Only if every other glazed opening is protected too. Florida's wind mitigation form rates the home by its weakest glazed opening, so one unprotected window keeps the home at X. Keep the slider's approval paperwork and a photo of its label for the inspector, and ask your insurer what your premium would be at Level A once every opening is covered.
Sources
- Florida Building Commission / FIU, Reviewing the Standards for Wind-Driven Rain Intrusion through Tracks of Sliding Glass Doors (Nov. 2024)
- FEMA Recovery Advisory USVI-RA4 (March 2018): Design, Installation, and Retrofit of Doors, Windows, and Shutters
- Florida Building Code, Building, 8th Ed. (2023), Chapter 17 (UpCodes)
- Florida Building Code, Building, 8th Ed. (2023), Chapter 16 (UpCodes)
- Florida Building Code, Building, 8th Ed. (2023), Chapter 1 (UpCodes)
- Miami-Dade County: Windows, Shutters, Doors and Security Bars
- Miami-Dade County: Product Control Search
- Miami-Dade County Implementing Order 4-63, Fee Schedule (effective Oct. 1, 2026)
- DASMA TDS 168: Wind on Garage Doors FAQ (exposure categories)
- Florida Statutes 718.113 (condominium hurricane protection)
- Laws of Florida ch. 2025-175
- Florida OIR Form OIR-B1-1802, Rev. 04/26
- Today's Homeowner: How Much Do Hurricane Windows Cost? (updated Sept. 3, 2025)
- Fixr: Hurricane Shutters Cost (updated Jan. 31, 2025)
- Florida Statutes 215.5586, My Safe Florida Home Program
- Texas Department of Insurance: Adopted Building Codes
- Texas Department of Insurance: Windstorm inspection process
- Texas Department of Insurance: Protecting openings FAQ
- TWIA: Windstorm Certification
- Texas Department of Insurance: Do you need a windstorm inspection?
This guide was written by our editorial team from the public sources listed above. It is general information, not legal advice; confirm licensing and terms directly with any provider.


