New ebook: Before You Borrow, how lenders decide and how to get your business loan approved. Get it for $7.99 →
New ebookHow to Research Like a Wall Street AnalystFind original sources, analyze trends, build your own insightsGet it now →
Markets
Real businesses. Bigger perspective. · Fri, Nov 20, 2026News. Tools. Scores. Games. Free.The Morning Chronicle
Donate BTCOpen dDashboard

Local Guide · Hurricane shutters and impact windows

How Do You Maintain Hurricane Shutters and Impact Windows? An Annual Pre-Season Checklist for Florida and Texas

Shutters that jam, panels missing their wing nuts and impact windows with clogged weep holes fail when you need them. This system-by-system guide covers what to check every spring before the June 1 season start, how to fight salt-air corrosion on the Atlantic and Gulf coasts, and why upkeep can affect your insurance credit.

Check every hurricane shutter and impact window each spring, before the Atlantic season opens June 1. Operate each shutter fully, clean and rinse tracks, lubricate moving parts with the product the manufacturer specifies, count and inspect panel hardware, and test motors and manual overrides. For impact windows, clean the glass and frames, clear the weep holes, and look for failed seals or sealant. Openings in poor condition can cost you a wind mitigation credit in Florida.

Key facts

  • The Atlantic hurricane season runs June 1 through November 30. (Ready.gov)
  • Florida's wind mitigation form, OIR-B1-1802 (Rev. 04/26), says all openings must be in good condition, and buildings with openings that need replacement do not qualify for wind mitigation rate differentials. (Florida OIR form)
  • Citizens Property Insurance wind inspectors look at storm shutters and panels whether installed or stored on the property. (Citizens)
  • For removable panels, TDI advises having the installer pre-mark each panel and leave a layout plan and instructions, and practicing installation on one or two openings before a storm. (Texas Department of Insurance)
  • Florida's code requires corrosion-resistant attachment hardware permanently installed on the building for plywood or OSB storm panels, with nuts or bolts of at least 1/4 inch and washers at least 1 inch in outside diameter. (FBC Residential R301.2.1.2)
  • IBHS lists sealing gaps around doors and windows with caulk or weatherstripping among affordable hurricane-readiness steps homeowners can do themselves. (IBHS / FORTIFIED)
  • TDI says replacing the glass in windows or doors does not need a Texas windstorm inspection. (Texas Department of Insurance)
  • Florida condominium boards must adopt hurricane protection specifications for each building, and installing, maintaining, repairing, replacing and operating hurricane protection under those rules is not a material alteration of the common elements. (Florida Statutes 718.113(5))
  • The garage door industry association warns occupants never to adjust or repair garage door springs or anything fastened to them, because they are under extreme tension. (DASMA TDS 167 and 174)

Why does shutter and window maintenance matter?

Hurricane protection is only as good as its weakest opening on the day of the storm. A roll-down shutter whose motor has seized, an accordion shutter that will not slide past a corroded track, or a stack of aluminum panels missing half its wing nuts leaves a hole in the house. Once wind gets inside, pressure pushes up on the roof and out on the walls. IBHS and TDI both describe a breached opening as a structural threat, not only a water problem.

Maintenance also has a paperwork side:

  • Florida insurance credits. The Uniform Mitigation Verification Inspection Form, OIR-B1-1802 (Rev. 04/26), rates the weakest opening protection on the house and states that all openings must be in good condition. A home with openings that need replacement does not qualify for wind mitigation rate differentials. A cracked impact pane or a broken shutter can cost the credit for the whole house.
  • Inspections count what you have. Citizens' wind inspectors check storm shutters and panels whether installed or stored on the property. Missing panels or hardware may mean an opening is rated as unprotected.
  • Approvals assume the product is intact. Product approvals (Florida product approval, Miami-Dade Notice of Acceptance, or a TDI product evaluation) cover the product as tested and installed with specific parts. Substituting look-alike bolts or tracks can mean the opening no longer matches the approval.

The good news: most of this is inexpensive. A garden hose, mild soap, a soft brush, the right lubricant, a flashlight and an afternoon cover most homes.

When should I do hurricane shutter maintenance?

Do the full check every year in the spring, finishing by late May so you are ready when the season opens June 1. Supply shortages and contractor backlogs come fast once a storm is forecast. A practical calendar:

WhenWhat to do
March to MayFull inspection of every shutter and window. Order missing hardware and replacement panels. Book any professional service for motors or repairs.
Late MayDry run: put up one or two panels, close every accordion and roll-down shutter, test manual overrides.
June to NovemberQuick monthly look; rinse salt off coastal shutters. Re-check hardware before any watch is issued.
After every stormInspect for dents, bent tracks, cracked glass and loose anchors before stowing anything.
DecemberClean, dry and store panels and fabric screens. Note any damage to fix before spring.

If you live within sight of salt water in places such as Miami Beach, Clearwater, Galveston or Port Aransas, rinse exposed shutters and tracks more often. See the salt-air section below.

How do I protect shutters from salt-air corrosion?

Salt spray is the main enemy of shutters on the Atlantic and Gulf coasts. Salt deposits hold moisture against metal, attack aluminum finishes, rust steel hardware and seize moving parts. Corrosion is often worst where you cannot easily see it: inside tracks, behind headers, around embedded anchors and on the underside of panels in storage.

  1. Rinse with fresh water. Hose off tracks, slats, accordion blades, hinges and exposed anchors. Rinse from the top down. Close to the beach, do this every few weeks in season.
  2. Wash, then rinse. Use mild soap and a soft brush for built-up grime. Avoid harsh cleaners and abrasive pads that strip protective coatings on aluminum.
  3. Dry and inspect. Look for white powdery oxidation on aluminum, orange rust on steel, bubbling paint and pitting around fasteners.
  4. Check anchors and sleeves. Permanent wall anchors for panels are the part most often forgotten. Florida's code requires corrosion-resistant attachment hardware permanently installed on the building for wood structural panels, and manufactured panels list their own anchors in the product approval. Replace any anchor that is loose, rusted through, stripped or missing.
  5. Use matching hardware. Mixing metals, such as plain steel bolts in aluminum tracks, can speed corrosion. Use the hardware listed in your product's approval or installation instructions.

If an aluminum track or shutter is pitted badly enough to bind or deform, have a licensed contractor evaluate repair versus replacement. A shutter that cannot close fully is not protecting the opening.

What lubricant is best for hurricane shutters?

Use the lubricant your shutter's manufacturer or installer specifies; it is in the owner's instructions or available from the company that sold the system. As a general approach:

  • Clean before you lubricate. Lubricant on top of sand and salt makes a grinding paste.
  • Favor products that do not attract grit for tracks, wheels and slides, such as a dry silicone spray, if your manufacturer allows it.
  • Avoid heavy grease and general oils in open tracks unless specified, because they collect dirt and can stain surfaces.
  • Lubricate locks and keyways with a product made for locks, then operate the lock several times.
  • Do not lubricate brake or clutch parts inside a roll-down motor or crank gearbox yourself. Those belong to a service technician.

After lubricating, run the shutter through its full travel two or three times and wipe off any excess.

How do I maintain accordion shutters?

Accordion shutters fold out of upper and lower tracks and lock in the middle or at one end. They fail when tracks fill with debris or corrode, when wheels or rollers break, or when locks seize. Annual steps:

  1. Open and close every accordion fully. Note any spot that drags or sticks.
  2. Clean the bottom track first. Vacuum or brush out leaves, sand, insects and lizard nests. Then rinse. The bottom track collects most of the debris.
  3. Clean the top track and the blades. Wash both faces of the blades and rinse.
  4. Check wheels and rollers. Cracked, flat-spotted or missing wheels make the shutter hard to move and can let it jump the track. Replace with manufacturer parts.
  5. Lubricate tracks and wheels with the specified product.
  6. Test the locks. Make sure you have the key or tool for every lock and that the center lock engages fully. Keep spare keys with your hurricane kit.
  7. Look at the mounting. Check that tracks are tight to the wall and that no anchors have pulled loose.

More detail on the product type is in our accordion shutter guide.

How do I test motorized roll-down shutters?

Roll-down shutters have a box (hood) above the opening, slats that roll into it, side tracks and either a manual crank or an electric motor. Test them in spring:

  1. Run each shutter all the way down and up using its switch or remote. Listen for grinding, clicking or the motor straining.
  2. Check the limits. The shutter should stop at the fully closed and fully open positions on its own. If it overruns or stops short, the limit settings need service.
  3. Test the manual override. Most motorized shutters have a crank or other manual means. Find it, use it, and make sure every adult in the home can. In a storm the power often fails before the shutters are needed most.
  4. Inspect slats and the bottom bar for dents, cracks and broken end retention clips. A slat that has popped out of the track is a weak point.
  5. Clean the side tracks and rinse. Keep the base of each track free of mulch, sand and plants.
  6. Check the bottom locks or locking bar, if your system has one.

Who services roll-down motors?

Motors, gearboxes, limit switches and internal springs should be serviced by the installing company, a dealer for that manufacturer, or a licensed contractor experienced with that system. Ask for the motor brand and model during installation and keep it with your records. In Florida, work on shutters generally requires an appropriately licensed contractor; see Florida licensing for window and shutter installers. In Texas, see Texas contractor rules.

Do not leave motorized shutters closed over bedroom escape windows while people are home outside a storm threat. Florida's residential code allows shutters over escape openings only during the threat of a storm, with at least one first-floor way out kept open.

How do I maintain storm panels and their hardware?

Steel, aluminum and clear polycarbonate panels are inexpensive and strong, but they depend on two things you can lose track of: the panels themselves and the small parts that hold them. TDI's advice for removable panels is simple and worth following: have the installer pre-mark each panel and leave a layout plan and installation instructions, then practice installing covers on one or two openings at your leisure to learn the time and difficulty.

Panel and hardware inventory

ItemWhat to checkWhen to replace
PanelsCount against your layout plan. Check each panel's label or mark.Bent, creased, cracked (polycarbonate), or corroded through
Wing nuts, washers and boltsCount them. Make sure threads turn freely.Rusted, stripped, or missing washers
Wall anchors or sleevesEach one present, tight, clean insideLoose, spinning, cracked surrounding wall, corroded
Headers and sill tracks (if used)Straight, tight to the wall, drains clearBent, pulled away from wall
ToolsWrench or driver for your hardware, ladder, glovesMissing or wrong size

For plywood or OSB panels used as a code-allowed option, the Florida Building Code, Residential, requires 1/4-inch minimum hex nuts, washered wing nuts or bolts, with washers at least 1 inch in outside diameter, attached to corrosion-resistant anchors permanently installed on the building. For manufactured aluminum, steel or polycarbonate panels, use the exact hardware listed in the product approval. See our guides to storm panels and plywood protection.

Storing panels

  • Store flat or upright in a dry place, sorted by opening, with the hardware bagged and labeled.
  • Keep polycarbonate out of long sun exposure in storage and away from solvents, unless the manufacturer says otherwise.
  • Do not store panels where they block the garage door track or the path to the electrical panel.
  • Photograph the stacked, labeled panels each year. It helps a wind mitigation inspector and an insurance claim.

How do I care for fabric hurricane screens?

Fabric screens are woven, coated panels that attach to anchors or tracks around the opening. They are light and easy to store but can be damaged by sun, mildew and sharp edges.

  • Unroll each screen in spring and inspect for tears, abrasion, failed seams and damaged grommets or straps.
  • Clean with mild soap and water, rinse, and let them dry completely before rolling. Storing a damp screen invites mildew.
  • Check every anchor, strap and buckle against the installation instructions.
  • Store rolled, not folded sharply, in the bag provided, away from rodents and sharp tools.

Any repair beyond what the manufacturer allows may mean the screen no longer matches its approval. See fabric hurricane screens.

How do I maintain colonial and Bahama shutters?

Colonial (side-hinged) and Bahama (top-hinged) shutters stay on the house all year, so they face constant sun and salt. Check hinges and pins for corrosion and wear, make sure the stays or arms that prop Bahama shutters open are secure, and confirm every locking bar, bolt or pin needed to close them for a storm is present. Close each pair fully at least once a year, because hinges that never move tend to seize. Decorative shutters that are not hurricane rated do not count as protection; TDI lists decorative shutters among items that do not need a windstorm inspection. See colonial and Bahama shutters.

How do I clean and maintain impact windows?

Impact windows need less storm-season work than shutters, but they still need care. The goals are keeping water draining properly, keeping seals intact and spotting damage early.

Cleaning impact glass

  • Rinse off dust and salt first so grit does not scratch the glass while you wipe.
  • Wash with mild soap or a non-abrasive glass cleaner and a soft cloth or squeegee.
  • Avoid razor blades, steel wool and abrasive powders, which can scratch glass and damage coatings or the exposed edge of the laminated interlayer. Check the manufacturer's care instructions, especially for coated or tinted glass.
  • Clean frames with mild soap and water. Do not pressure-wash directly at seals, weep holes or the joint between frame and wall.

Weep holes: the step most people miss

Most windows, impact or not, are designed to let some water into the sill and then drain it outside through small openings called weep holes, usually on the exterior face of the bottom frame. When weep holes clog with dirt, sand, insects or paint, water backs up and can overflow onto the interior sill or into the wall.

  1. Find the weep holes on each window and sliding door, often small slots with flaps or covers.
  2. Clear them gently with a soft brush, pipe cleaner or low-pressure water. Do not drill or enlarge them.
  3. Pour a little water into the sill track and watch it drain outside.
  4. Never caulk or paint over weep holes.

Seals, weatherstripping and sealant

  • Weatherstripping: Open each sash or slider and look at the gaskets and pile strips. Replace any that are torn, flattened or missing, using the manufacturer's parts. IBHS lists sealing gaps around windows and doors with caulk or weatherstripping as an affordable readiness step.
  • Perimeter sealant: Look at the joint between the frame and the wall outside. Cracked, shrunken or pulled-away sealant lets wind-driven rain in. Re-sealing is routine, but do not seal the weep holes or the sill drainage path.
  • Fogging between panes: If an insulated impact window fogs or shows moisture between the panes, the insulating glass seal has failed. The window still holds its laminated lite, but performance drops. Check your warranty.
  • Cloudiness or bubbles at the glass edge: Possible delamination of the interlayer. Photograph it and contact the manufacturer or installer.

Sliding door tracks and hardware

Vacuum the track, wipe it clean, and check that rollers glide. Operate locks and handles. Heavy impact sliders put more load on rollers, so a door that drags needs adjustment by a technician. See impact sliding glass doors.

Do impact window seals need replacing, and can I replace the glass?

Weatherstripping and perimeter sealant wear out over time and can be replaced as maintenance. A cracked impact pane, failed insulating glass or delaminated interlayer is a repair that should use glass matching the window's approval.

  • Florida: The glass in an approved impact window is part of the tested assembly. Ask the original manufacturer or a licensed contractor for glass that matches the product approval. Under Florida's energy code, replacing only the glass in an existing sash and frame is treated as a repair, not an alteration. Check with your building department whether a permit is needed in your city or county.
  • Texas coast: TDI says replacing the glass in windows or doors does not need a windstorm inspection. Replacing the whole window does, if you want to keep TWIA eligibility. See TDI windstorm certification.

A cracked impact pane is still a reason to act quickly in Florida, because the 1802 form says openings needing replacement do not qualify for mitigation credits.

What about garage doors?

The garage door is the largest opening on most homes. The Door and Access Systems Manufacturers Association (DASMA) publishes a homeowner checklist (TDS 167) and a post-storm inspection guide (TDS 174). Key safe steps for owners:

  • With the door closed, look at springs, cables, hinges, brackets, tracks and fasteners for damage or looseness. Look, do not touch, the springs.
  • Check that the jambs and header are firmly attached to the framing.
  • Pull the operator's disconnect, then lift the door by hand. It should move smoothly, stay in its tracks, and stay up when fully open.
  • Test any manual locks or wind bracing that came with your door.
  • Re-connect the operator and test the auto-reverse.

DASMA warns occupants never to remove, adjust or repair springs or anything fastened to them. Call a trained door technician. See garage door bracing and retrofits.

Who maintains shutters in a condo or HOA?

In Florida condominiums, the answer depends on the declaration. Section 718.113(5) requires each residential condominium board to adopt hurricane protection specifications for each building, and states that installing, maintaining, repairing, replacing and operating hurricane protection under that subsection is not a material alteration of the common elements. Whether the association or the unit owner pays for maintenance of shutters, windows and doors depends on who is responsible under the declaration. If the association removes your hurricane protection to do its own maintenance work, unless the declaration says otherwise you are not responsible for the cost of removing and reinstalling it.

Florida HOAs are governed by s. 720.3035, which defines hurricane protection to include permanent fixed storm shutters, roll-down track shutters, impact windows and doors, polycarbonate panels and reinforced garage doors, among other items. Read your documents and get the board's specifications in writing before replacing parts. See condo hurricane protection and HOA hurricane protection.

Texas condominium and HOA rules come from the governing documents and the Texas Property Code; check with your association manager for maintenance responsibility.

What is a pre-season shutter inspection, and do I need one?

A pre-season inspection is a paid visit, usually in spring, in which a shutter company or licensed contractor operates every shutter, services motors, replaces worn wheels and seals, and lists hardware to replace. It is worth considering if you have many roll-down shutters, an older system, a high-rise unit, or limited ability to handle panels yourself.

Before you hire anyone, verify the license (Florida DBPR or your county; your Texas city's registration requirements), get the scope and price in writing, and be wary of door-to-door offers to "inspect" shutters that turn into a sales pitch for replacement. See storm chaser scams and how to choose a contractor.

What should I check after a hurricane?

Before stowing anything after a storm:

  • Photograph every shutter and window before you open or remove anything. These photos help an insurance claim.
  • Look for dents in panels and slats, bent tracks, cracked or crazed impact glass, and anchors pulled from the wall.
  • Check for water stains inside around windows, which may mean blocked weep holes or failed sealant.
  • Remove panels carefully; wind-loaded panels can be bent and under tension.
  • Rinse salt off everything before storage.
  • Report damage to your insurer promptly. In Texas, TDI says TWIA policyholders have one year from the storm to file a claim.

See hurricane damage claims and repairs.

How to choose a provider

  • By late May, operate every shutter through its full travel.
  • Clean and rinse all tracks, starting with accordion bottom tracks; rinse salt off monthly near the coast.
  • Lubricate tracks, wheels and locks with the manufacturer's specified product.
  • Count panels against the layout plan and count every wing nut, washer and bolt.
  • Inspect every permanent wall anchor and sleeve; replace any loose or corroded.
  • Test roll-down motors, limits and the manual override; teach every adult how to use it.
  • Unroll and inspect fabric screens; dry fully before storing.
  • Clean impact glass gently; never use razors or abrasives on coated glass.
  • Clear weep holes on every window and sliding door and test that sills drain.
  • Replace torn weatherstripping and cracked perimeter sealant, without sealing drainage paths.
  • Run the DASMA-style garage door check; leave springs to a technician.
  • Photograph shutters, stored panels and windows for insurance and your 1802 inspection.
  • Fix cracked impact glass or broken shutters before your wind mitigation inspection.

Related hurricane shutters and impact windows guides

Hurricane shutters and impact windows by state and city

Questions people ask

How often should accordion shutter tracks be cleaned?

At least once a year in spring, with a full open-and-close test, plus a rinse after storms and whenever debris builds up. Homes close to salt water benefit from rinsing tracks every few weeks during hurricane season, because salt deposits hold moisture and speed corrosion. Always clean the bottom track first, since sand, leaves and insects collect there and are the most common reason an accordion shutter sticks when you need it.

Can I use a general-purpose spray oil on hurricane shutters?

Use whatever lubricant your shutter manufacturer specifies. Many owners use a dry silicone spray on tracks and wheels because it does not hold sand the way oily products can, but manufacturers differ. Clean the track first, apply lightly, run the shutter several times and wipe off the excess. Use a lock lubricant in keyways, and leave motor and gearbox internals to a service technician.

How long do hurricane shutters last?

It depends on the material, how close you are to salt water and how well they are maintained. We found no independent, dated study giving reliable service life numbers for shutter types, so be cautious of any single figure. Signs a shutter is near the end of its useful life include deep pitting, bent or cracked tracks, slats that keep popping out, and repeated motor failures. A licensed contractor can tell you whether repair parts are still available.

Do I need to maintain impact windows if I have no shutters?

Yes. Clean the glass gently, clear weep holes so sills drain, check weatherstripping and the exterior sealant joint, and look for cracks, fogging between panes or cloudy edges that could mean delamination. In Florida, a cracked or failed opening matters for insurance, because the OIR-B1-1802 form says openings needing replacement do not qualify for wind mitigation rate differentials.

What should I keep in my shutter hardware kit?

Every wing nut, washer and bolt your panels need, plus a few spares of each, the wrench or driver that fits them, keys for accordion locks, the crank for manual roll-down overrides, gloves, a sturdy ladder, your panel layout plan and the installation instructions. Store it with the panels and check it each spring. TDI recommends practicing installation on one or two openings before a storm so you know how long it takes.

Does maintenance affect my wind mitigation inspection?

It can. Florida's OIR-B1-1802 form rates the weakest opening protection on the house and requires all openings to be in good condition. Citizens' inspectors check shutters and panels whether installed or stored. If panels are missing, hardware is gone, or a shutter is broken, the inspector may not be able to give credit for that opening, which can lower the rating for the whole home. Have your product approvals and photos ready.

Who should service my roll-down shutter motor?

The company that installed it, a dealer for that manufacturer, or a licensed contractor experienced with that system. Motors, limit switches, gearboxes and internal springs are not owner-service items. Ask during installation for the motor make and model and the service contact, and keep that with your records. Schedule service in early spring, because demand rises sharply once a storm is forecast.

Sources

This guide was written by our editorial team from the public sources listed above. It is general information, not legal advice; confirm licensing and terms directly with any provider.

New ebook from The Company ChronicleHow to Research Like a Wall Street AnalystFind original sources, analyze trends, and build your own insights. 36 pages with worksheets.Get the ebook · $29Instant PDF download

Business Spotlight

Want us to publish your business?

Our team writes and publishes articles about your business on The Company Chronicle every month, with a link to your website. Plans from $30 a month, cancel anytime.

Publish with us

The Chronicle directory

What are you into?

The Chronicle, coast to coast

Every corner has a story.

The full Chronicle illustration