New ebook: Before You Borrow, how lenders decide and how to get your business loan approved. Get it for $7.99 →
New ebookHow to Research Like a Wall Street AnalystFind original sources, analyze trends, build your own insightsGet it now →
Markets
Real businesses. Bigger perspective. · Fri, Nov 20, 2026News. Tools. Scores. Games. Free.The Morning Chronicle
Donate BTCOpen dDashboard

Local Guide · Hurricane shutters and impact windows

What Are Impact Windows and How Do They Survive a Hurricane? Laminated Glass, Frames and Ratings Explained

An impact window is a complete, tested system of laminated glass, frame and anchors that stays closed even when debris cracks the glass. Here is how each part works, how the tests are run, and how to tell whether the windows on a house are really impact rated.

Impact windows are window units built with laminated glass (glass layers bonded to a tough plastic interlayer) set in a reinforced frame and anchored to the wall exactly as tested. When debris hits, the glass may crack, but the interlayer holds it in the frame so wind and rain stay out. They are tested as a whole unit against a 9-lb 2x4 missile and thousands of pressure cycles. Cracked impact glass still protects through the storm but must be replaced afterward.

Key facts

  • TDI says impact windows are tested as a unit that includes the glass, frame, attachment hardware and installation method, and that the frame matters as much as the glass.
  • FLASH says impact glass 'must be installed as a complete window system, including the frame' and cannot be added to existing frames.
  • The HVHZ large missile is a 9-lb 2x4 fired at 50 feet per second (80 feet per second for Risk Category IV essential facilities) (FBC 1626.2.3).
  • HVHZ specimens take two missile impacts, then 9,000 pressure cycles (4,500 inward, 4,500 outward); they pass with no penetration and no crack longer than 5 inches and wider than 1/16 inch through which air can pass (FBC 1626.2, Table 1626).
  • Florida requires exterior windows to carry a permanent label, marking or etching traceable to the manufacturer and product, plus a label (permanent or temporary) showing design pressure, impact rating if any, and the FL# or NOA, kept on until final inspection (FBC 1709.5.1).
  • Openings within 30 feet of grade need large-missile protection; higher openings need at least small-missile protection (FBC 1609.1.2).
  • TDI says it is not necessary to install shutters over impact-resistant windows.
  • On Florida's 2026 wind mitigation form, all openings must be in good condition; openings needing replacement keep the home from qualifying for wind mitigation rate differentials.

What makes a window an impact window?

An ordinary window keeps out weather. An impact window also keeps the opening closed after being hit by wind-borne debris and then pounded by hours of gusting wind pressure. Three things make that possible, and they only work together:

  1. Laminated glass: at least two layers (lites) of glass permanently bonded to a plastic interlayer.
  2. A frame built to hold that glass: deeper glazing pockets, reinforced sash and frame members, and stronger locks and hardware.
  3. Anchoring and installation as tested: the specific screws or anchors, spacing, shims, bucks and sealants listed in the product approval.

The Texas Department of Insurance puts it plainly: impact windows are tested as a unit that includes the glass, frame, attachment hardware and installation method. FLASH adds that impact glass cannot be slipped into an existing frame; it must be installed as a complete window system. If any part is swapped, the tested rating no longer applies.

How laminated glass works

Laminated glass is made by bonding glass lites to an interlayer under heat and pressure, usually in an autoclave, so that the layers act as one panel. A familiar example is a car windshield: FLASH notes that impact glass is similar to the laminated windshield in your car. Like a windshield, it may crack or break, but it does not readily come apart.

When a 2x4 hits it, the outer lite may break. The interlayer stretches and absorbs energy while holding the broken pieces. If the impact does not fully penetrate, the glass shows a 'spider web' of cracks but stays in one sheet. That sheet still blocks wind and rain, which is the whole point: an unbroken envelope keeps pressure from building inside the house. IBHS explains that broken windows let in wind and rain and create internal pressures that push up and out on the roof and walls.

Other benefits of lamination

  • UV: suitable interlayers block nearly all ultraviolet light, which reduces fading of floors and furniture.
  • Sound: laminated glass reduces sound more effectively than single (monolithic) glass of the same thickness; special acoustic interlayers do more.
  • Safety and security: broken glass stays bonded instead of falling as sharp shards, and the panel resists a quick break-in. See security benefits.

The interlayer: PVB vs. ionoplast (SGP)

The interlayer is the heart of impact glass. The two families you will hear about:

PVB (polyvinyl butyral)Ionoplast (often called SGP, after a trade name)
What it isThe long-established standard interlayer for architectural and automotive laminated glassA stiffer, stronger ionomer interlayer
Stiffness and strengthSofter and more flexibleAn interlayer maker states ionoplast offers 'substantially higher strength and stiffness' than PVB
Where usedMany residential impact windows and doorsUsed where more stiffness is wanted; the maker says it allows thinner, lighter glass builds without losing safety
What to checkThe approval lists the exact glass and interlayer makeup testedSame: the approval governs

Other interlayers exist, including EVA and TPU. For a buyer, the practical point is that you do not choose the interlayer separately; you choose a tested product whose approval lists the glass makeup. Miami-Dade requires window permit plans to show the glass type and thickness and the options chosen from the product approval, so the interlayer is fixed by the approval, not by a salesperson.

Monolithic laminated vs. laminated insulated glass

Monolithic laminatedLaminated insulated (laminated IGU)
BuildOne laminated panel (glass + interlayer + glass)A sealed insulating unit with an air or gas space; one pane (or both) is laminated, often with a separate outboard pane
EnergySimilar to a single pane; low-E coatings can help with solar heatBetter insulating value because of the sealed space
NoiseGoodOften better, especially with an acoustic interlayer
Weight and frame depthLighter, thinnerHeavier, thicker; needs a deeper frame
CostUsually lowerUsually higher
After a hitThe laminated panel holdsAn outboard non-laminated pane may break as a 'sacrificial' pane while the laminated pane holds

Florida's residential code even refers to 'outboard sacrificial panes in laminated insulating glass units' in its safety glazing rules, a sign of how common the design is. Which build you need depends on your energy goals and the product line; both can carry impact approvals. See energy efficiency and noise.

Impact glass vs. tempered glass

People mix these up, and it matters.

  • Tempered glass is heat-treated to be stronger than ordinary (annealed) glass and to break into small, blunt pieces. It is safety glazing, required in places like doors and near tubs. But when it breaks, it falls out of the frame, leaving the opening open.
  • Laminated impact glass may crack but stays bonded to the interlayer and in the frame, so the opening stays closed.

Tempered or heat-strengthened lites can be part of a laminated impact makeup, but tempered glass by itself is not impact protection. A window etched 'tempered' is not an impact window. Florida's safety glazing rule requires permanent marks on safety glass in hazardous locations, which is one of the etchings you may see in the corner of a pane, so read what the mark actually says.

Frames: aluminum vs. vinyl

FactorAluminumVinyl (PVC), usually reinforced
Strength and slim profilesStrong; allows narrower frames and large unitsBulkier profiles; often steel or aluminum reinforced inside
Heat transferConducts heat; look for thermally broken framesInsulates better
Salt airFinish and hardware must resist corrosionDoes not corrode, but hardware and reinforcement still can
Common usesCoastal homes, condos, high-rises, storefrontsMany single-family homes
What decides suitabilityDesign pressure and size in the approvalDesign pressure and size in the approval

Neither material is 'best' for every house. Choose the product whose approval meets your openings' required design pressure at the sizes you need, then weigh energy, looks and salt exposure. See design pressure ratings explained.

Window styles: single-hung, casement, horizontal roller and fixed

StyleHow it opensStrengthsWatch-outs
Single-hungBottom sash slides upFamiliar, generally economical, works as a bedroom egress window if sized rightOnly half opens for air
CasementHinged on side, cranks outSeals tightly; full opening for air and egressCrank hardware to maintain; sash swings outside
Horizontal roller (slider)Sash slides sidewaysWide openings; simpleTracks need cleaning
AwningHinged at top, opens outCan vent in light rainSmaller opening; not usually egress
Fixed (picture)Does not openNo moving sash, so product lines often reach their highest design pressures and largest sizes hereNo air or escape; not for required bedroom egress

Design pressure ratings and maximum sizes differ by style within the same product line, so a quote that uses one rating for every window should be questioned. Check each unit's line in the approval.

Egress and fall protection when you replace windows

Every sleeping room needs an escape opening of at least 5.7 square feet (5 square feet at grade floor), 24 inches high and 20 inches wide, with the sill no higher than 44 inches (FBC Residential R310). Florida's Existing Building Code lets a replacement window in a required escape opening skip the new-construction size rules if it is the manufacturer's largest standard size that fits the existing opening (FBC-EB 505.3). Replacing certain operable windows can also trigger window fall prevention devices meeting ASTM F2090, depending on sill height (FBC-EB 702.4).

How impact windows are tested

Impact windows earn their rating in a lab, not in a brochure. In Florida's High-Velocity Hurricane Zone (Miami-Dade and Broward), the test sequence is:

  1. Large missile impacts (TAS 201): a 9-lb 2x4 fired at 50 feet per second (80 feet per second for essential facilities) at three specimens, two hits each: one near the center and one near a corner (FBC 1626.2).
  2. Cyclic pressure (TAS 203): 9,000 cycles, half pushing in and half pulling out, each lasting 1 to 3 seconds, up to a set fraction of the design load (Table 1626).
  3. Pass/fail: no penetration, and no crack longer than 5 inches and wider than 1/16 inch through which air can pass (FBC 1626.2.8).
  4. Uniform static pressure (TAS 202): confirms the design pressure rating, along with air and water tests.

Outside the HVHZ, products are typically tested to ASTM E1886 (the test method) and ASTM E1996 (the performance specification), which set missile levels and wind zones. Above 30 feet, the small missile test (2-gram steel balls in the HVHZ protocol) can apply instead. For the details and missile levels, see missile impact testing standards.

Note on marketing words: TDI warns that a product described as rated for 'Force 12' winds meets only the minimum of a Category 1 hurricane, 74 mph. Ask for the test standard and design pressure.

Do impact windows break? What happens after a hit?

The glass can crack; that is expected and allowed by the test. What should not happen is penetration or the glass falling out. After a storm:

  • During the storm, a cracked impact window is still doing its job. Leave it alone.
  • After the storm, photograph the damage for your insurance claim, then schedule replacement. A cracked laminated pane has used up much of its capacity and may not survive another hit or a long pressure cycle.
  • Insurance: Florida's 2026 wind mitigation form says all windows and doors must be in good condition; openings that need replacement keep the home from qualifying for wind mitigation rate differentials, regardless of other features. Repairing promptly protects your discount.
  • Replacement: in many cases the glass can be reglazed with the same approved makeup by a qualified installer; in others the sash or whole unit must be replaced. Either way, use parts that match the approval. A replacement or reglaze may need a permit; ask your building department.

See window damage claims and repairs.

Are impact windows bulletproof?

No. Impact standards test resistance to wind-borne debris and wind pressure, not firearms. Bullet-resistant glazing is a separate class of product tested to different standards, and impact windows should never be described as bulletproof. They do resist casual smash-and-grab entry better than ordinary glass because the laminate holds together.

How can I tell if my windows are impact rated?

This matters for buying, selling, insurance and wind mitigation inspections. Work through these checks:

  1. Look for a permanent mark. Florida requires exterior windows to carry a permanent label, marking or etching that traces to the manufacturer and product (FBC 1709.5.1). Many manufacturers etch a small mark in a corner of each glass pane. Read it: it may name the manufacturer and an impact or laminated designation, or it may only say 'tempered', which is not impact.
  2. Check the temporary label (new installs). The code requires either a permanent label or a temporary supplemental label with the design pressures, impact rating, maximum size tested, test standards and FL# or NOA, kept on until final inspection. Photograph it before it is removed.
  3. Check the permit history. Your city or county building department can show window permits, which list the product approval numbers.
  4. Look up the approval. Use the FL# or NOA in the Florida Building Commission or Miami-Dade Product Control databases. See NOA lookup and Florida product approval lookup.
  5. Ask for the paperwork. Sellers, builders and installers often have NOA letters. Citizens recommends giving NOA letters to your wind mitigation inspector so features that are not clearly marked still earn discounts.
  6. Look at the glass edge. Laminated glass usually shows a faint line of interlayer at the edge, but frames often hide it. This alone is not proof.
  7. Hire a wind mitigation inspector. Florida's form OIR-B1-1802 requires photos or documents for each attribute marked, including opening protection.

Example: If you are buying a 2005 house in Tampa and the seller says 'all hurricane windows', ask for the permit numbers and NOA letters. If the glass shows only 'tempered' marks and there are no records, the windows may be ordinary, and the wind mit form will likely not give opening protection credit.

Do impact windows need shutters too?

No. TDI says that while shutters over impact windows add protection if the outer system failed, installing both is not necessary. Florida's code treats impact-resistant glazing alone as meeting the windborne debris rule (FBC 1609.1.2; R301.2.1.2). Some owners shutter very exposed openings anyway. For the choice between the two, see impact windows vs. hurricane shutters.

How long do impact windows last?

We found no neutral, dated study of impact window lifespan in Florida or Texas, so we will not quote years. Life depends on frame material, salt exposure, sun, installation quality and maintenance. Insulated units can lose their seal over time and fog between panes. Hardware and weatherstripping wear. Read the written warranty, which often treats glass, frame, hardware and seal failure separately, and look for salt-air or coastal exclusions.

Simple upkeep

  • Keep sill tracks and weep holes clear so water drains.
  • Rinse frames near salt water; clean glass with non-abrasive cleaners.
  • Check locks, keepers and operators each season.
  • Inspect exterior sealant at the frame and repair cracks.

Installation: why it is half the rating

The approval drawings specify fasteners, spacing, edge distance, embedment, shims, bucks (wood or concrete framing around the opening) and sealants. Florida requires installation per the manufacturer's instructions and approval. Some details to know:

  • Sealed drawings: Florida does not require sealed drawings to replace windows on an existing one- or two-family home or townhouse if units are installed per the manufacturer's instructions for the wind zone (FBC 107.1.1).
  • Design pressure on the plans: Miami-Dade requires plans to show each window's required positive and negative design pressures and the glass type chosen from the approval.
  • Threshold buildings: under a binding interpretation ratified by the Florida Building Commission on January 26, 2026, window and door installations in threshold buildings (more than three stories or 50 feet tall, among others) need a threshold inspection; Miami-Dade now asks for wind calculations and wood buck calculations. See high-rise condo projects.
  • Existing homes: replacement windows generally must meet Chapter 16, with limited exceptions (FBC-EB 707.4). See window replacement code rules.

For the step-by-step process, see impact window installation process.

Texas and Florida specifics

Florida: impact windows must carry an FL# or Miami-Dade NOA; in Miami-Dade and Broward, the approval must be valid for the HVHZ, where FBC 1626.1 requires all glazing to meet impact criteria or be protected. Florida law bars marketing a product as hurricane protection without approval (s. 553.842(5)). Wind mitigation inspectors look for etching, labels and documents. The My Safe Florida Home program can fund impact windows for eligible homes when recommended by its inspection; its applicant portal has been offline since November 10, 2026 for a platform move. See My Safe Florida Home.

Texas: the products are the same, but the paperwork differs. On the coast, windows installed for TWIA eligibility need a TDI-accepted product evaluation, installation exactly per that evaluation, and inspection during installation to earn a WPI-8. TWIA lists windows among improvements that need a certificate of compliance. Since April 1, 2026, TDI certifies to the 2024 IRC/IBC. Replacing only the glass in a window does not need a windstorm inspection, per TDI, but replacing the window does. In Houston, Dallas, San Antonio and Austin, outside TDI catastrophe areas, local codes govern. See TWIA windstorm certification.

How to choose a provider

  • Confirm each window's required design pressure for its location on the house.
  • Get the FL#, NOA or TDI evaluation for every unit quoted.
  • Check that each style and size is listed in the approval at that pressure.
  • Decide monolithic laminated vs. laminated insulated based on energy goals.
  • Plan bedroom egress sizes for replacement units.
  • Make sure the permit (Florida) or WPI-1 and inspections (Texas coast) are in the contract.
  • Photograph temporary labels before they come off.
  • Keep NOAs, permits and photos for your wind mitigation inspection.
  • Replace any cracked impact glass promptly after a storm.
  • Clean tracks and weep holes each season.

Related hurricane shutters and impact windows guides

Hurricane shutters and impact windows by state and city

Questions people ask

What is the difference between impact windows and storm windows?

Storm windows are extra panes added over an existing window, mostly for weather and energy. Impact windows are complete tested units with laminated glass and reinforced frames that resist wind-borne debris and pressure. A storm window is not hurricane protection unless it carries an impact approval.

Can I put impact glass in my existing frames?

Generally no. FLASH says impact glass must be installed as a complete window system including the frame, and TDI says windows are tested as a unit. Putting laminated glass in an ordinary frame does not create a rated impact window and will not count for code or insurance.

Where is the impact window label or etching?

Look in a corner of each glass pane for an etched or printed mark, and on the frame for a permanent label. New windows also carry a temporary label with design pressures and the FL# or NOA until final inspection. If you cannot find marks, check permit records and approval paperwork.

Do impact windows count for Florida insurance discounts?

Yes. Documented large-missile impact windows can be rated Level A on Florida's wind mitigation form. Every opening on the house must be protected, because the form rates the weakest one, and all openings must be in good condition. Give the inspector NOA letters and permit records.

Are impact windows worth it?

They are worth it when you want protection without deploying shutters, need second-floor protection, or are replacing old windows anyway. FLASH notes their cost can be comparable to mid- to upper-range windows or to standard windows plus shutters. Compare written quotes and your insurer's credit before deciding.

Do impact windows block noise?

Laminated glass reduces sound more than single glass of the same thickness, and insulated laminated units with acoustic interlayers do more. Results depend on the product and installation. Ask for sound ratings in writing if noise is a main reason you are buying.

Can impact windows be opened like normal windows?

Yes. Operable impact windows such as single-hung, casement and sliders open normally, and they can serve as bedroom escape openings if sized to the code minimums. Fixed units do not open. Because they stay unshuttered, impact windows keep escape routes usable during a storm.

Do impact windows protect against storm surge or flooding?

No. They are tested for wind-borne debris and wind pressure, not for water forces from surge or flooding. Flood protection needs different measures. Follow evacuation orders for surge zones regardless of your windows, and see your flood insurance and elevation options separately.

What design pressure do I need?

It depends on your wind speed, exposure, building height and where the window sits on the wall; corners usually need more. Your contractor or designer calculates it, and Miami-Dade requires it on the permit plans. Compare it with each unit's rating in the approval.

Sources

This guide was written by our editorial team from the public sources listed above. It is general information, not legal advice; confirm licensing and terms directly with any provider.

New ebook from The Company ChronicleHow to Research Like a Wall Street AnalystFind original sources, analyze trends, and build your own insights. 36 pages with worksheets.Get the ebook · $29Instant PDF download

Business Spotlight

Want us to publish your business?

Our team writes and publishes articles about your business on The Company Chronicle every month, with a link to your website. Plans from $30 a month, cancel anytime.

Publish with us

The Chronicle directory

What are you into?

The Chronicle, coast to coast

Every corner has a story.

The full Chronicle illustration