New ebook: Before You Borrow, how lenders decide and how to get your business loan approved. Get it for $7.99 →
New ebookHow to Research Like a Wall Street AnalystFind original sources, analyze trends, build your own insightsGet it now →
Markets
Real businesses. Bigger perspective. · Thu, Nov 19, 2026News. Tools. Scores. Games. Free.The Morning Chronicle
Donate BTCOpen dDashboard

Local Guide · Hurricane shutters and impact windows

Impact Entry Doors and French Doors: What Are the Ratings, Costs and Rules, and What Should You Look For?

How impact-rated entry and French doors are tested and approved as complete assemblies, when Florida and Texas require them, what water ratings mean, where doors fail, why pet doors and hardware swaps can void an approval, and what drives the price.

An impact-rated door is a complete door assembly (slab, frame, glass, hinges, locks, bolts and anchors) tested to resist a 9-pound 2x4 missile and thousands of pressure cycles, then approved by Florida or Miami-Dade. In Miami-Dade and Broward every exterior door must be impact rated or protected; elsewhere in Florida's debris region, glazed doors must be. Changing parts, such as adding a pet door, can void the approval.

Key facts

  • FBC 1626.1 requires outside doors in the HVHZ (Miami-Dade and Broward) to meet impact test criteria or be protected by a device that does.
  • Outside the HVHZ, FBC 1609.1.2 requires glazed openings, including glass in doors, in wind-borne debris regions to be impact resistant or protected.
  • FBC 1709.5.1 requires side-hinged exterior doors to be tested and labeled to AAMA/WDMA/CSA 101/I.S.2/A440 or to comply with 1709.5.2 (ASTM E330 or TAS 202 at 1.5 times design pressure).
  • Under FBC 1709.5, doors with an overhang ratio of 1 or more (overhang length divided by height from sill to overhang) need not be tested for water infiltration.
  • Florida's 2026 wind mitigation form rates verified non-glazed entry doors tested for pressure (ASTM E330, ANSI/DASMA 108 or TAS 202) as Level D, which can lower a home's opening protection sub-answer.
  • FEMA says wind pressure failure of personnel doors is rare and usually traces to inadequate latch throw, hinge attachment or frame attachment; the most common hurricane door problem is water at the threshold, jambs and head.
  • The 2025 FORTIFIED Home standard exempts dog doors up to 3 sq ft in exterior walls from impact rating, but a dog door in an impact-rated door must be part of the tested assembly or the whole opening must be shuttered.
  • Fixr (Jan. 2025) puts a standard, non-impact entry door installation at $975 to $1,773, averaging $1,353; impact doors cost more.
  • TWIA lists entry doors among improvements needing a windstorm Certificate of Compliance in the Texas catastrophe area.

What is an impact-rated door?

An impact-rated door is not just a strong slab. It is a complete, tested assembly: the door leaf (slab), the frame, any glass, the hinges, the lock and latch, any flush bolts or astragal (the strip where a pair of doors meet), the threshold and the anchors that fasten the frame to the wall. The whole unit goes through the same kind of testing as an impact window:

  • Impact: a 9-pound 2x4 "large missile" fired at 50 feet per second, hitting the door at specified points (TAS 201 or ASTM E1886/E1996).
  • Cyclic pressure: thousands of push-pull pressure cycles after the impact to simulate hours of gusts (TAS 203 or ASTM E1886). In the HVHZ, Table 1626 calls for 9,000 cycles.
  • Static pressure, air and water: uniform pressure tests that set the design pressure (DP) rating, plus air and water infiltration tests (TAS 202, or AAMA/WDMA/CSA 101/I.S.2/A440).

Miami-Dade approvals for doors often add a forced entry test. A sample NOA for an aluminum outswing French door lists air infiltration, uniform static air pressure and water resistance per TAS 202, large missile impact per TAS 201, cyclic wind pressure per TAS 203, and forced entry per FBC 2411 and TAS 202.

The Texas Department of Insurance makes the same point for windows: impact products are tested as a unit, including the glass, frame, attachment hardware and installation method. Swap one part and you no longer have the tested unit.

A door that passes impact testing is labeled "impact resistant" or "L.M.I." (large missile impact) and carries a Florida product approval or Miami-Dade Notice of Acceptance. A door that passes only pressure tests is "wind rated" but not impact rated. That difference matters for both code and insurance. See missile impact testing standards.

Do you need an impact front door in Florida?

It depends on where you live, whether the door has glass, and whether the work is new or a replacement.

SituationWhat the Florida Building Code requires
Miami-Dade or Broward (HVHZ), any exterior doorImpact rated or protected by an approved device (FBC 1626.1), and tested to TAS 202 for pressure
Wind-borne debris region elsewhere, door with glassThe glazing must be impact resistant or protected (FBC 1609.1.2; Residential R301.2.1.2)
Wind-borne debris region elsewhere, solid door (no glass)Must meet design pressure (FBC 1709.5); the debris rule in 1609.1.2 is written for glazed openings
Outside the debris regionDesign pressure rating still required; impact rating generally not
Replacing an existing exterior doorMust comply with FBC Chapter 16 (FBC Existing Building 707.4), with a limited 25%-per-year exception for glazed openings in certain older homes

The wind-borne debris region covers areas within 1 mile of the coast where the design wind speed is 130 mph or more, and anywhere the design wind speed is 140 mph or more. Much of coastal Florida, including Tampa Bay, the Atlantic coast and the Panhandle beaches, falls in it, but inland Orlando sites generally do not. Ask your building department about your address.

The replacement exception. FBC Existing Building 707.4 lets one- and two-family homes built under codes other than the Florida Building Code replace glazed doors without opening protection if the replaced glazing in any 12-month period stays within 25% of the home's total glazed area, as long as the products are designed for enclosed-building wind pressures. In the HVHZ, the exception applies to homes built under codes in effect before September 1, 1994. Using it saves money now but means the door earns no opening protection credit and needs a shutter before storms.

Even when it is not required, consider it. On Florida's wind mitigation form, a solid entry door that is only pressure rated is Level D. If your windows are all Level A, a Level D door moves you to sub-answer A.2 instead of A.1. Whether that changes your premium depends on your insurer's rating plan. See the wind mitigation form and opening protection.

Texas: entry doors and windstorm certification

In the Texas Department of Insurance catastrophe area (the 14 first-tier coastal counties and parts of Harris County east of State Highway 146), a replacement entry door is an improvement that needs a windstorm Certificate of Compliance (WPI-8) for the home to stay eligible for TWIA coverage. TWIA's list of improvements needing certification includes windows, entry doors and garage doors.

  • Before work: file Form WPI-1 with TDI. TDI inspectors charge no fee and must inspect during construction, so the frame and anchors are visible.
  • Code: since April 1, 2026, work must be certified to the 2024 International Residential Code or International Building Code. TDI says most catastrophe areas are now in the wind-borne debris region.
  • Products: TDI tells homeowners to use opening protection tested to ASTM E1886 and E1996 and designated by a recognized product approval. TDI publishes product evaluations on its Windstorm System.
  • What does not need an inspection: TDI lists replacement of glass in windows or doors, screen doors and decorative shutters among projects that do not need a windstorm inspection.
  • Payment: TDI advises not to pay in full until the work is done and the WPI-8 is issued.

Homes in Houston, Dallas, San Antonio and Austin outside the catastrophe area follow local codes only. See TWIA windstorm certification for windows and doors.

The whole assembly is approved: frame, glass, hardware and anchors

This is the part most buyers miss. A door's approval covers a specific combination of parts installed a specific way. Real Miami-Dade NOAs for doors show how specific:

  • Design pressure depends on the configuration. "Lower DP ratings shall apply for entire assembly, when doors are mulled w/ Sidelites." A door rated higher than its sidelite takes the sidelite's lower number.
  • Required hardware. One French door NOA requires two manually operated flush bolts (top and bottom) on single doors and on both leaves of double doors. Leave one off and the door is not the approved door.
  • Size limits. "Door w/ transom is limited to max. 25-1/2" h Transom."
  • Glass support. "Glass lite wider than 36" shall be supported with approved setting blocks or clamps."
  • Substrate. Some approvals note that the structural capacity of a steel substrate is to be reviewed by the building official, and anchor schedules differ for concrete, block and wood framing.

The Florida Building Code gives some flexibility. Under FBC 1709.5.3, door components evaluated by an approved evaluation entity, certification agency, testing lab or engineer may be interchanged in exterior door assemblies if they provide equal or greater structural performance, shown by accepted engineering practice. And under the custom-door exception in 1709.5, a one-of-a-kind door may be tested by an approved lab or engineered by a Florida-registered design professional, with signed and sealed calculations given to the building official at permit application.

Without that documentation, a mixed-and-matched door is not an approved assembly. In the HVHZ in particular, inspectors compare the installed door with the approval drawings.

Labels

FBC 1709.5.1 requires exterior doors to carry a permanent label, marking or etching traceable to the manufacturer and product. A temporary supplemental label, which must stay on until final approval by the building official, shows the manufacturer, model or series, positive and negative design pressure, maximum size tested, impact rating if any, Florida or Miami-Dade approval number, test standards and the certification or testing agency. Photograph both before the temporary label comes off. See how to read a Miami-Dade NOA.

Out-swing vs. in-swing doors: does the direction matter?

Many impact entry and French doors sold in South Florida are out-swing (they open toward the outside), and several of the Miami-Dade door NOAs we examined are for out-swing units. Both types are available with approvals. We found no primary source that ranks one over the other by test data, so here is what can be said with confidence, and what to check.

  • The approval is what counts. An in-swing door and an out-swing door are different assemblies with different approvals, design pressures and water ratings. Compare the actual numbers on each approval for your size and configuration, not the swing direction.
  • How wind loads the door. Positive pressure pushes a door inward and negative pressure (suction) pulls it out. An out-swing door is pushed against its frame stops by positive pressure, while an in-swing door relies more on its latch, bolts and hinges against that inward push; under suction the roles reverse. That is why approvals specify latches, flush bolts and hinge fastening, and why FEMA's post-hurricane observations found door failures usually trace to inadequate latch throw, hinge attachment or frame attachment.
  • Water. Water at the threshold is the most common door problem in hurricanes, according to FEMA. Look at the approval's water test result and the threshold design, not the swing direction alone.
  • Practical issues. Out-swing doors need clear space outside (porch, steps, shutters), hinges with non-removable pins for security, and a plan for any storm shutter, since an out-swing door cannot open with a closed shutter in front of it.

If you are choosing between the two, ask each supplier for the approval, then compare: design pressure (both directions), water resistance test pressure, impact rating, and forced entry testing.

Water penetration ratings vs. design pressure

A door can be strong enough not to blow in and still leak. These are two different ratings.

RatingWhat it measuresWhere to find it
Design pressure (DP)The wind pressure, in psf, the door can resist without failing, positive (inward) and negative (outward)Label and approval tables; tested to 1.5 times DP
Water resistanceWhether water passes through the closed door while it is sprayed under a test pressureApproval test reports (TAS 202 water resistance, or the AAMA/WDMA/CSA 101 water test)
Air infiltrationHow much air leaks throughApproval test reports
ImpactWhether it resists the missile and then the pressure cyclesApproval impact rating

The water test pressure is normally much lower than the structural design pressure, which is why doors that survive a hurricane structurally can still let water in. FEMA's 2018 recovery advisory on doors and windows in the U.S. Virgin Islands puts it plainly: the most common door problem during hurricanes is surface water and wind-driven rain entering at the gap between the door and the threshold, jamb or head, and even with excellent detailing, it is challenging to avoid water infiltration during strong hurricanes, especially where low thresholds are required for accessibility.

When the code skips the water test

FBC 1709.5 lets door assemblies skip water infiltration testing in two cases: in nonhabitable areas designed to accept water, and where the overhang ratio is 1 or more. The overhang ratio is the overhang's projection from the door face divided by the height from the door sill to the bottom of the overhang. Example: a porch roof that sticks out 8 feet with its underside 8 feet above the sill has a ratio of 1. A door under a deep porch can therefore be approved without a water rating, so if you move it to an exposed wall, it may leak.

How to reduce door leaks

  • Choose a door whose approval shows a water test at a meaningful pressure, and ask for a high-performance threshold.
  • FEMA recommends adjustable jamb and head weatherstripping, such as wide sponge EPDM rubber, kept adjusted for good contact.
  • Before a storm, FEMA suggests checking weatherstripping and notes some owners apply expanding foam at sill gaps, which can be hard to remove.
  • Slope the ground away from doors with swales or berms; FEMA documented a house where water ran down the driveway into the entry door.
  • For businesses, FEMA suggests vestibules with water-resistant floors and drains, and exterior trench drains at thresholds.
  • Proper flashing at installation matters as much as the door. FEMA cites ASTM E2112 as the installation practice aimed at minimizing water infiltration.

For more on water ratings for sliders, where the problem is worst, see impact sliding glass doors.

Do doors with glass need laminated impact glass?

Yes, if the door must be impact rated. Any glass in a door is a glazed opening. In the HVHZ, every door must meet impact criteria; in the wind-borne debris region elsewhere, glazed openings must be impact resistant or protected. The glass in an impact door is laminated: layers of glass bonded to a plastic interlayer that holds the pieces in place after it cracks. NOAs list the specific interlayer products approved for that door.

  • Small decorative lites are still glazing. The door must be approved with that lite, or the opening protected.
  • Sidelites and transoms are separate glazed units. They must be part of the approval (most door NOAs cover approved sidelite and transom configurations) and the lowest DP of the combination controls.
  • Replacing broken glass must use the glass type and thickness in the approval. In Texas, TDI says replacing glass in a door does not need a windstorm inspection, but the glass still has to match the product's rating to keep it.
  • Insurance: on Florida's form, glazed doors are rated with windows in the "Windows or Entry Doors" glazed column; a non-impact glazed door with no shutter makes the whole house X.

Fiberglass, steel, aluminum or wood: which impact door is better?

There is no code ranking of door materials. What matters is the tested rating for your size and configuration. TDI makes the same point about shutters: galvanized and aluminum shutters tested to the same standard should perform the same. Compare doors by their approvals, then by how the material suits your house.

MaterialStrengthsWatch for
FiberglassResists denting; holds paint or stain finishes; good insulationCheck the approval for your size with glass options
SteelStrong and often lower cost for solid doorsDents; rust at cut edges and the bottom rail near salt water
Aluminum (glazed doors)Slim frames for large glass; common for French and patio doorsFinish quality near the coast; thermal performance unless thermally broken
WoodAppearance, historic homesFewer impact-approved options; finish maintenance; moisture

On cost, Fixr's 2025 entry door guide ranks aluminum and composite as "very affordable," steel and fiberglass as "fairly affordable," and solid wood and glass as "fairly expensive" for standard doors. Impact versions follow a similar pattern but at higher prices. Near salt water, ask about stainless or coated hinges and fasteners. Corroded hardware is a common reason older protection fails or is marked damaged. See historic homes if you are matching an older facade.

Impact French doors and double doors

Impact French doors are widely available, including out-swing pairs with sidelites. One sample Miami-Dade NOA covers an aluminum out-swing French door "w/wo Sidelites" rated for large and small missile impact. Double doors are harder to make storm-tight than single doors because the two leaves meet in the middle with no fixed frame member.

  • The inactive leaf must be locked to the frame. Approvals often require top and bottom flush bolts on the inactive leaf, and the one we reviewed required them on both leaves of double doors.
  • The astragal (the strip where the leaves meet) carries load and seals the gap. Damage or poor adjustment here is a leak and failure point.
  • Multi-point locks, when part of the approval, spread the load along the edge.
  • DP is usually lower than for a single door of the same height, and the combination with sidelites takes the lowest rating.

Before a storm: make sure every bolt is fully engaged, the astragal is undamaged, and weatherstripping is in good contact.

Where impact doors fail: thresholds, astragals, latches and frames

FEMA's post-hurricane observations give a clear picture. Wind pressure failure of personnel doors is rare. When it happens, it is typically due to:

  • Inadequate latch throw: the bolt does not extend far enough into the strike
  • Inadequate attachment of hinges: short screws into the frame or the framing behind it
  • Inadequate attachment of the door frame to the building: the type, size, spacing and edge distance of frame fasteners

FEMA says such deficiencies can often be fixed cost-effectively with new hardware or fasteners. The far more common problem is water: at the threshold, then the jambs and head.

Failure pointWhat to check
Threshold and sillSealed to the floor, sill pan or flashing in place, weeps clear, threshold height per the approval
Astragal (pairs)Undamaged, seals in contact, flush bolts fully engaged
Latch and strikeFull bolt engagement; strike fastened into framing
HingesAll screws present and long enough per the approval
Frame anchorsType and spacing per the anchor schedule; no corrosion
WeatherstrippingContinuous, compressed, not torn
GlassNo cracks or delamination; glazing beads tight

Do pet doors, smart locks or other changes void an impact rating?

They can, because the approval covers the tested assembly and nothing else. Here is what the sources actually say:

  • Pet doors. The 2025 FORTIFIED Home standard (from the Insurance Institute for Business and Home Safety) exempts dog doors up to 3 square feet installed in exterior walls from impact-rating requirements, but says dog doors located in impact-rated window and door assemblies must either be included in the tested assembly or the entire opening must be protected by an impact-rated system. In other words, cutting a pet door into an impact door breaks the rating unless that combination was tested and approved.
  • Termination clauses. Miami-Dade NOAs state that termination occurs if there is a change in the materials, use or manufacture of the product, and that failure to comply with any section of the NOA is cause for termination.
  • Hardware swaps. FBC 1709.5.3 allows interchangeable door components only when an approved evaluation entity, lab or engineer shows equal or greater structural performance. A new lockset or smart lock that changes the bore, latch, strike or bolt may or may not meet that test. We found no code provision addressing smart locks specifically. Before replacing a lock on an impact door, ask the door manufacturer whether the new hardware is approved for that door, and keep the answer in writing.
  • Glass and lites. Replacing a solid panel with glass, or changing the glass type, creates a different product.
  • Insurance. If a mitigation inspector cannot verify the door as approved, it may be rated N (unverified) or lower.

Can you paint or stain an impact door?

We found no code provision that treats paint or stain as a modification to the approval. Follow the manufacturer's finishing instructions, since they control the warranty, and do not paint over the permanent label or etching. Mitigation inspectors and building officials rely on those labels, and Citizens Property Insurance says features that are not clearly marked may need NOA documentation to earn discounts.

Can you put a shutter over a non-impact door instead?

Yes. The code allows glazed openings to be impact resistant or protected with an impact-resistant covering (FBC 1609.1.2 and, in the HVHZ, 1626.1). Accordion, roll-down and fabric systems are common over doors. Considerations:

  • The door still needs a design pressure rating. FEMA notes that if debris protection is provided by shutters, the glazing is still required by ASCE 7 to meet the positive and negative design pressures.
  • Shutters do not stop water. FEMA says shutters over windows should not be relied on to protect against wind-driven rain.
  • Getting out. If the shuttered door is your main exit, you cannot leave until the shutter is opened. Plan at least one usable exit.
  • Out-swing doors cannot open with a shutter closed in front of them.
  • Insurance treats an approved shutter the same as an impact door for the debris rating, if documented.

For the cost comparison, see hurricane shutter costs.

How much does an impact front door cost?

We could not find a reliable, dated, independent cost study for impact entry doors in Florida or Texas, so we will not give you a made-up average. Here is what we can source and what moves the price.

  • Baseline, non-impact: Fixr's entry door guide (updated January 31, 2025) puts standard entry door installation at $975 to $1,773, averaging $1,353, with labor at $67 to $121 per hour and 3 to 7 hours of work. It says double and French doors of the same material cost about twice as much as a single pre-hung door, and that storm and security doors are "much more expensive." Impact doors cost more than this baseline.
  • Price drivers: single vs. double, sidelites and transoms, glass area and type, material, design pressure, HVHZ approval, out-swing vs. in-swing hardware, multi-point locks, custom sizes, and whether the opening must be resized.
  • Hidden costs: stucco and interior trim repair around the frame, threshold and floor transitions, buck or framing repair, and disposal.
  • Permits: unincorporated Miami-Dade charges $150.82 for a single-family window or door installation permit, or $133.38 plus a $25.65 up-front fee for an exact change-out under its residential hardening permit type (fee schedule effective Oct. 1, 2026). Miami-Dade's checklist for solid doors (less than 50% glass) uses permit category 104.

Get at least three quotes listing the exact approval number, DP and configuration. See impact window costs for the general cost logic, which applies to doors too.

Grants and discounts

Florida's My Safe Florida Home grants may pay for exterior doors as opening protection when the program's inspection recommends them, matched $2 state to $1 homeowner up to $10,000, and DFS may require all openings to be improved. The applicant portal has been offline since November 10, 2026 for a platform move. See My Safe Florida Home.

Permits, installation and inspection

  • Permit: replacement doors generally need a permit in coastal Florida. Miami-Dade's door checklist asks for the building permit application (category 104 for doors without glass or with less than 50% glass), the total door area, a contact sheet, an elevation of each wall showing which doors are replaced and their sizes, and the product approval number and current NOA for each door. Florida Building Commission approvals are acceptable.
  • Engineering: FBC 107.1.1 says sealed drawings are not required to replace doors on an existing one- or two-family home or townhouse if they are installed per the manufacturer's instructions for the wind zone, meet current FBC Residential design pressures, are the same size in the same opening, and the instructions are submitted with the permit. Resizing an opening or a threshold building changes that.
  • Threshold buildings: since January 26, 2026, all window and door installations in Florida threshold buildings (more than three stories or 50 feet) need a threshold inspection by a state-certified Special Inspector and a special inspection plan.
  • After a declared disaster: Tampa's 2026 post-hurricane guide waives permits for size-for-size front or rear exterior door replacement only while the Mayor's emergency powers are in effect; relocating, closing or resizing a door opening always needs a permit.
  • Licensing: in Florida, Specialty Structure Contractors may install door assemblies in Group R buildings up to three stories or 30 feet; taller buildings need a Division I contractor. See Florida licensing for installers.

How doors are rated on Florida's wind mitigation form

Question 9 of Florida's Uniform Mitigation Verification Inspection Form (OIR-B1-1802, Rev. 04/26) treats doors in two groups:

  • Glazed doors (entry doors with glass, French doors, sliders) are rated with windows in the glazed-openings column. They help set the main answer: A, B, C, N, X or Z, based on the weakest glazed opening.
  • Non-glazed doors (solid entry doors and solid garage doors) set the sub-answer. For a house rated A, sub-answer A.1 means all non-glazed openings are also Level A (or there are none); A.2 means one or more are Level D (pressure rated only) and none are B, C, N or X; A.3 means one or more non-glazed openings are B, C, N, X or Z.
Your solid front doorLikely levelEffect if windows are all Level A
Impact rated, documentedAA.1
Pressure rated only (ASTM E330, ANSI/DASMA 108 or TAS 202), documentedDA.2
Unknown or undocumentedN or XA.3
DamagedZHome does not qualify for mitigation rate differentials

The form requires at least one photo or document proving each attribute, and all openings must be in good condition. Products must be listed in the Florida or Miami-Dade approval system to count as Level A or B. Keep the door's approval and a label photo for the inspector. How much each sub-answer changes your premium depends on your insurer's filed rating plan; ask your agent.

Commercial and storefront doors

Storefront doors are usually part of a storefront or window wall system with its own approval. Miami-Dade storefront and window wall NOAs commonly state that doors and windows are under separate approvals and that the lower design pressure controls the entire system. For a business, that means the weakest door sets the rating for the whole storefront.

Commercial door work in unincorporated Miami-Dade is permitted at $0.164 per square foot of window or door area under the October 2026 fee schedule, and buildings over three stories or 50 feet now need threshold inspections for window and door installations. In Texas, commercial structures in the catastrophe area need windstorm certification to the 2024 IBC for TWIA eligibility. See commercial building hurricane protection.

Security benefits of impact doors

Impact doors are heavier and their glass is laminated, so a broken lite stays in the frame instead of falling out. Many Miami-Dade door approvals include forced-entry testing under TAS 202. That said, an impact rating is a storm rating, not a burglary rating, and security depends on the lock, strike and frame anchorage too. FEMA's observation that door failures usually trace to latch throw, hinge fastening and frame anchorage applies to intruders as much as wind. See security benefits of impact windows and doors.

How to choose a provider

  • Confirm whether you are in the HVHZ or the wind-borne debris region before choosing a door.
  • Get the Florida approval or NOA number for the exact door, sidelites and transom you are buying.
  • Check the design pressure for your configuration; the lowest rating in a mulled unit controls.
  • Read the approval's water resistance test and ask about a high-performance threshold.
  • Make sure required hardware (flush bolts, multi-point locks, hinge screws) is included and installed.
  • Do not add a pet door, change glass or swap locks unless the manufacturer confirms the change is approved.
  • Photograph the temporary and permanent labels before the temporary label is removed.
  • Confirm who pulls the permit and that the final inspection passes before final payment.
  • In the Texas catastrophe area, file WPI-1 before work and get the WPI-8 before paying in full.
  • Before each storm, check bolts, astragal, weatherstripping and the threshold seal.
  • Give your wind mitigation inspector the approval paperwork for every exterior door.

Related hurricane shutters and impact windows guides

Hurricane shutters and impact windows by state and city

Questions people ask

Do impact doors need to open outward?

No. Both out-swing and in-swing impact doors are available with Florida or Miami-Dade approvals. What matters is the tested rating for your exact door: design pressure in both directions, water resistance and impact rating. Out-swing doors are common in South Florida, but each design has trade-offs, such as needing clear space outside and not opening with a shutter closed in front of it.

What is the difference between a wind-rated and an impact-rated door?

A wind-rated door has passed pressure testing for a design pressure, for example under ASTM E330, ANSI/DASMA 108 or TAS 202. An impact-rated door has also passed missile impact and cyclic pressure tests, such as TAS 201 and 203 or ASTM E1886 and E1996. On Florida's mitigation form, a verified wind-rated solid door is Level D; an impact-rated door is Level A.

Does a solid front door with no glass need to be impact rated?

In Miami-Dade and Broward, yes: FBC 1626.1 covers outside doors. Elsewhere in Florida, the debris-region rule in 1609.1.2 is written for glazed openings, so a solid door must meet design pressure but not necessarily impact. On the mitigation form, a pressure-rated solid door can still hold your home at sub-answer A.2 instead of A.1.

Can I replace just the lockset on my impact door?

Only with hardware the door's approval allows. FBC 1709.5.3 permits interchangeable door components when an approved evaluation entity, lab or engineer shows equal or greater structural performance. Some approvals require specific hardware such as flush bolts. Ask the manufacturer before installing a new lock or smart lock and keep its written answer with your records.

Will my impact door stop all water during a hurricane?

Not necessarily. Structural strength and water resistance are separate ratings, and the water test pressure is much lower than the design pressure. FEMA says water at the threshold, jambs and head is the most common door problem in hurricanes, and it is hard to avoid entirely in strong storms, especially with low accessible thresholds. Good flashing, thresholds and weatherstripping reduce it.

Is a pet door allowed in an impact door?

Only if the door with that pet door was tested and approved as an assembly. The 2025 FORTIFIED Home standard says dog doors in impact-rated window and door assemblies must be part of the tested assembly, or the whole opening must be protected by an impact-rated system. A dog door up to 3 square feet in a wall, not in the door, is exempt under FORTIFIED.

Do condo owners need association approval for a new impact front door?

In Florida condos, usually yes. Florida Statutes 718.113(5) requires boards to adopt hurricane protection specifications, which can include exterior windows and doors, and a board may not refuse an installation that conforms to those specifications, though it may require you to follow the building's unified exterior look. Check the declaration, get written approval before ordering, and confirm the door meets the building's specs.

What questions should I ask before buying an impact door?

Ask for the Florida approval or NOA number for the exact configuration, the design pressure for your size, the water resistance test result, whether it passed large missile impact and forced entry testing, what hardware is required, how the frame anchors into your wall type, who pulls the permit, and the product and labor warranty terms. Compare at least three quotes on the same specification.

Do I need an impact door in Orlando?

Often not by code, because much of inland Orange County is outside the wind-borne debris region; your door still needs a design pressure rating. Check with your building department for your address. Many inland owners still choose impact doors for security, noise and insurance reasons, but the mitigation credit depends on every opening being protected.

Sources

This guide was written by our editorial team from the public sources listed above. It is general information, not legal advice; confirm licensing and terms directly with any provider.

New ebook from The Company ChronicleHow to Research Like a Wall Street AnalystFind original sources, analyze trends, and build your own insights. 36 pages with worksheets.Get the ebook · $29Instant PDF download

Business Spotlight

Want us to publish your business?

Our team writes and publishes articles about your business on The Company Chronicle every month, with a link to your website. Plans from $30 a month, cancel anytime.

Publish with us

The Chronicle directory

What are you into?

The Chronicle, coast to coast

Every corner has a story.

The full Chronicle illustration