Local Guide · Hurricane shutters and impact windows
Hurricane Protection Rules by Florida County: Miami-Dade, Broward, Palm Beach, the Keys, Southwest Florida, Tampa Bay, Orlando, Jacksonville and the Panhandle
Only two Florida counties are in the HVHZ, but most of the coast is in the wind-borne debris region. Here is a county-by-county matrix of mapped wind speeds, debris-region status, permit portals and the storms that shaped each region's rules.
Only Miami-Dade and Broward are in Florida's High-Velocity Hurricane Zone, where every opening must meet HVHZ impact tests (design speeds 175 and 170 mph). Everywhere else, the rule depends on the mapped wind speed at your address: glazed openings need impact protection if the site is at 140 mph or more, or at 130 mph or more within 1 mile of the coast. That covers all of Palm Beach, the Keys, Southwest Florida and Pinellas, part of Hillsborough, Pasco, Bay and Volusia, and generally not inland Orlando or Jacksonville.
Key facts
- The Florida Building Code defines the High-Velocity Hurricane Zone as Miami-Dade and Broward counties; Risk Category II design speeds are 175 mph and 170 mph (FBC 1620.2).
- Outside the HVHZ, the wind-borne debris region is within 1 mile of the coastal mean high water line where Vult is 130 mph or more, or anywhere Vult is 140 mph or more (FBC Chapter 2).
- The 2023 FBC (8th Edition) took effect December 31, 2023 and references ASCE 7-22; peninsula wind speeds are effectively unchanged since 2010, while western Panhandle speeds rose (Florida Building Commission fact sheet, June 2024).
- The University of Florida GeoPlan Center drew countywide wind speed maps for all 67 counties; local jurisdictions often modify them, so the building department's map controls.
- Miami-Dade says the 9th Edition (2026) FBC takes effect December 31, 2026.
- Plywood panels are allowed as opening protection outside the HVHZ only on low-rise homes where Vult is 180 mph or less (FBC 1609.1.2, R301.2.1.2).
- Florida's 2026 wind mitigation form (OIR-B1-1802 Rev. 04/26) classifies homes as HVHZ, Region 1 (140 mph or more), Region 2 (130 to 139 mph) or Region 3 (under 130 mph).
- Ch. 2026-63 (HB 803) requires local governments to exempt single-family work under $7,500 from building permits, except in flood hazard areas and for structural, electrical, plumbing, mechanical or gas work.
- NCEI says Hurricane Irma destroyed 25 percent and significantly damaged 65 percent of buildings in the Florida Keys in 2017.
How hurricane protection rules work in every Florida county
Florida has one statewide building code, the Florida Building Code (FBC). Every county and city enforces it, and local governments may add only limited local amendments. So the question "what does my county require?" really comes down to three facts about your exact property:
- Is it in the High-Velocity Hurricane Zone (HVHZ)? Only Miami-Dade and Broward counties are. If yes, every window, door, skylight and garage door must meet the HVHZ impact tests or be covered by an HVHZ-approved shutter, with no exceptions for upper floors or plywood. See our HVHZ guide.
- What is the ultimate design wind speed (Vult) at the site? Wind speed is mapped as contour lines that cross counties, not as one number per county. Two homes in the same county can have different design speeds.
- Is the site in the wind-borne debris region? The FBC defines this as the part of the hurricane-prone region within 1 mile of the coastal mean high water line where Vult is 130 mph or greater, or anywhere Vult is 140 mph or greater. Inside that region, glazed openings (windows, glass doors, skylights and glass in garage doors) must be impact resistant or protected by an approved impact-resistant covering.
Once you know those three answers, the rest follows the same statewide rules: product approval (a Florida approval number or Miami-Dade Notice of Acceptance), a permit from your local building department, and an inspection. The county affects which portal you file in, which design speed goes on the permit, and, in Miami-Dade and Broward, which test standards apply.
One more point that confuses buyers: the debris-region rules apply to new construction and to replacement work. They do not force an owner to retrofit an existing house that is not being worked on. The Florida Building Code, Existing Building, sets the rules for replacement windows and doors, including a limited exception for small replacements in older homes. Our replacement rules guide walks through it.
Which Florida counties are in the High-Velocity Hurricane Zone?
Only two: Miami-Dade and Broward. Florida's 2026 uniform mitigation form (OIR-B1-1802, Rev. 04/26) also identifies the HVHZ as Miami-Dade and Broward counties, and it treats the HVHZ as its own region, separate from Regions 1, 2 and 3.
The HVHZ has fixed design wind speeds written into the code (FBC Building Section 1620.2), so there is no contour map to read:
| County | Risk Category I | Risk Category II (most homes and offices) | Risk Category III | Risk Category IV (essential facilities) |
|---|---|---|---|---|
| Miami-Dade | 165 mph | 175 mph | 186 mph | 195 mph |
| Broward | 156 mph | 170 mph | 180 mph | 185 mph |
All HVHZ buildings are designed as at least Exposure Category C (FBC 1620.3). HVHZ products are tested under Florida's TAS 201, 202 and 203 protocols. The large missile is a 9-pound 2x4 fired at 50 feet per second, used for assemblies up to 30 feet above grade, and above 30 feet the glazing must pass a small missile test of 2-gram steel balls (FBC 1626.2 and 1626.3). Miami-Dade's Product Control Search lets you filter approvals by "High velocity hurricane zone" and "Non-High velocity hurricane zone", which is the quickest way to confirm a product is legal there. Our NOA lookup guide shows how.
Palm Beach and Monroe are not in the HVHZ. Many installers in Palm Beach County sell HVHZ-rated products, and many owners choose them, but the code does not require them there. Palm Beach and the Keys follow the general wind provisions (FBC Building 1609 and FBC Residential R301.2.1), with wind speeds that are still among the highest in the state.
What wind speed applies in my Florida county?
Outside the HVHZ, the design wind speed comes from maps in the code (FBC Building Figures 1609.3(1) through 1609.3(4), one per risk category). The 8th Edition (2023) FBC, effective December 31, 2023, references ASCE 7-22, the national wind load standard.
A Florida Building Commission fact sheet on the ASCE 7-22 changes (June 2024) explains what moved and what did not:
- Peninsula: wind speeds are unchanged and have effectively not changed since the 2010 FBC.
- Western Panhandle: wind speeds increased for Risk Category I, II and III buildings.
- Big Bend: Risk Category IV speeds decreased slightly; Category IV also rose in the western Panhandle.
- New tools: a new note on Figure 1609.3(1) allows site-specific speeds from the ASCE Wind Design Geodatabase (the free ASCE 7 Hazard Tool). The fact sheet warns that the older ATC Hazards by Location website does not support ASCE 7-22 and cannot be used for the 8th Edition.
- Local maps: the University of Florida GeoPlan Center drew countywide Vult maps for all 67 counties and all four risk categories. The fact sheet adds that local jurisdictions often modify these maps, so you should contact your local building department for a specific site.
The UF project report (June 2023) says 37 counties adopted the preliminary maps as drawn, 12 adopted versions adjusted to local landmarks with UF's help, and 13 drew their own landmark maps. That is why the county building department's adopted map, not a statewide chart, is the final word. Many counties draw the official line along a road or canal near where the contour falls.
How to find your number in five minutes:
- Open the ASCE 7 Hazard Tool, enter your address, choose ASCE 7-22 and Risk Category II (for a typical house).
- Write down the wind speed. Then check your building department's adopted wind speed map or ask the permit counter.
- Apply the debris-region test: 140 mph or more anywhere, or 130 mph or more within 1 mile of the coast, means glazed openings need impact protection.
- Ask your installer to show the design pressures for each opening on the permit drawings. Our design pressure guide explains the numbers.
Florida county matrix: wind speed, debris region and HVHZ
No single official table of design wind speed by county exists, because the lines cross counties. To build this matrix we read the contour lines on the University of Florida GeoPlan Center's preliminary countywide Risk Category II maps for the 2023 FBC (dated March 22, 2023), plus the fixed HVHZ speeds in FBC 1620.2. Treat the ranges as a starting point. Your county may have adopted a landmark-adjusted map, and the official speed for your lot comes from the ASCE 7 Hazard Tool or your building department.
| Region | County | Approx. Risk Category II Vult on the UF 2023 draft county map (mph) | Wind-borne debris region (applying the FBC definition) | HVHZ | Storm history hook |
|---|---|---|---|---|---|
| Southeast | Miami-Dade | 175 (fixed by code) | Yes, entire county (HVHZ rules) | Yes | Andrew (1992, Cat 5, Homestead) |
| Southeast | Broward | 170 (fixed by code) | Yes, entire county (HVHZ rules) | Yes | 1947 Cat 4 near Pompano Beach |
| Southeast | Palm Beach | About 150 (west) to about 170 (coast) | Yes, whole county is at or above 140 | No | 1928 Okeechobee hurricane (Jupiter); 1949 (Palm Beach Shores) |
| Keys | Monroe | About 160 to 170 on the mainland; about 170 to 180 and higher in the Keys | Yes | No | Irma (2017, Cat 4, Cudjoe Key); 1935 Labor Day (Craig Key) |
| Southwest | Collier | About 150 (northeast) to about 170 (southwest coast) | Yes | No | Donna (1960, Naples); Wilma (2005, Cape Romano) |
| Southwest | Lee | About 150 (northeast) to about 160 (Gulf coast) | Yes | No | Ian (2022, Cat 4, Cayo Costa) |
| Southwest | Charlotte | About 140 to 160; Punta Gorda near the 150 line | Yes | No | Charley (2004, Cat 4, Punta Gorda) |
| Southwest | Sarasota | About 145 to 155; the 150 line crosses the county | Yes | No | Milton (2024, Cat 3, Siesta Key) |
| Tampa Bay | Pinellas | Between the 140 and 150 lines county-wide | Yes, whole county is at or above 140 | No | Milton (2024, Cat 3) came ashore to the south at Siesta Key |
| Tampa Bay | Hillsborough | The 140 line runs through the Tampa area; higher to the southwest, lower to the northeast | Part of county; check the site | No | Milton (2024) landfall to the south at Siesta Key |
| Tampa Bay | Pasco | The 140 line crosses the county diagonally; the Gulf side is above 140 | Part of county; check the site | No | Helene (2024) came ashore to the north near Perry |
| Central | Orange (Orlando) | Between about 130 and 140; the 140 line touches the east edge | Mostly no (inland, under 140); check east edge | No | Inland; no landfall listed in the Florida Climate Center table |
| East coast | Brevard | About 140 (west) to about 150 (coast) | Yes, nearly all at or above 140 | No | Jeanne (2004, Hutchinson Island, to the south) |
| East coast | Volusia | About 130 (west) to about 140 (coast) | Coastal strip within 1 mile of the shore; check the site | No | Nicole (2022, near Vero Beach, to the south) |
| Northeast | Duval (Jacksonville) | Between about 120 and 130; the 130 line lies just offshore | Generally no; confirm beachfront sites | No | No major landfall listed in the Florida Climate Center table |
| Big Bend | Taylor (Perry) | About 120; the 120 line crosses the county | Generally no (below 130) | No | Helene (2024, Cat 4, near Perry); Idalia (2023, Keaton Beach) |
| Panhandle | Bay (Panama City) | About 130 (northeast) to 140 and higher (west and coast) | Part of county: areas at or above 140 plus a 1-mile coastal strip | No | Michael (2018, Cat 5, Mexico Beach) |
| Panhandle | Escambia (Pensacola) | About 140 (north) to about 160 (barrier island) | Yes, nearly all at or above 140 | No | Opal (1995, Pensacola Beach); Ivan (2004) |
How to read the debris column. We applied the FBC definition (140 mph or more anywhere, or 130 mph or more within 1 mile of the coast) to the mapped ranges. "Yes" means essentially the whole county meets the 140 mph trigger. "Part" means the 140 line crosses the county, so it depends on which side of the line you are on and how close you are to the water. Hospitals, schools used as shelters and other higher-risk buildings use different maps (Figures 1609.3(2) and 1609.3(3)), so their debris region is larger.
A caution on the debris definition. The 8th Edition first printed a narrower coastal trigger that added an "Exposure D upwind" condition. The Florida Building Commission's Structural Technical Advisory Committee voted 10 to 1 to recommend going back to the 7th Edition (2020) definition pending a study, and the current code text we checked uses the simpler 7th Edition wording quoted above. The UF draft maps still print the older draft wording in their margin. If your property is near the coastal line, ask the building department which definition it applies.
Storm landfall locations in the last column come from the Florida Climate Center at Florida State University and NOAA's National Centers for Environmental Information (NCEI).
Southeast Florida: Miami-Dade, Broward and Palm Beach
Miami-Dade County
Miami-Dade is the strictest place in the country for opening protection, and the reason is Hurricane Andrew. The National Weather Service in Miami says Andrew made landfall on August 24, 1992 at Fender Point near Homestead as a Category 5 with 165 mph sustained winds. NCEI says Andrew damaged or destroyed more than 125,000 homes in Dade County and that Florida building codes were strengthened afterward.
What that means today:
- Every product needs a current Miami-Dade NOA or a Florida product approval that covers HVHZ use. Miami-Dade accepts both for window, door and garage door permits.
- Stand-alone window, mullion and glass door replacement permits need a permit application (category 82 and/or 83), the total square footage being replaced, a front elevation of each affected wall, and the current NOA or Florida approval for each product. Plans must show the positive and negative design pressures and the glass type chosen from the approval's glass schedule.
- Licensed contractors can get residential accordion shutter and storm panel permits through the county's e-permitting system. Owners in unincorporated Miami-Dade (property folio starting with "30") can submit online through the county's permitting portal or in person at the Permitting and Inspection Center. If you live inside one of the county's cities, you file with that city.
- Condos and high-rises: a statewide binding interpretation ratified by the Florida Building Commission on January 26, 2026 requires every window and door installation in a threshold building (more than three stories or more than 50 feet tall) to get a threshold inspection by a state-certified special inspector and an inspection plan from the engineer of record. See our high-rise window guide.
- Code change ahead: Miami-Dade says the Florida Building Code, 9th Edition (2026), takes effect December 31, 2026, and applications submitted through its online portal after 4 PM on December 30, 2026 will be reviewed under the 2026 edition.
Broward County
Broward is also HVHZ, with a Risk Category II design speed of 170 mph. The same TAS tests, NOA or HVHZ-level Florida approvals, and no-plywood rule apply. Most Broward residents live in one of its cities, and each city runs its own building department, so start with your city's permit office. Broward's hurricane history includes a 1947 Category 4 landfall near Pompano Beach, according to the Florida Climate Center.
Palm Beach County
Palm Beach is outside the HVHZ, but its mapped Risk Category II speeds run from about 150 mph in the west to about 170 mph at the coast on the UF draft map, so the entire county is above the 140 mph debris trigger. In practice, every new or replacement glazed opening needs impact-rated glass or an approved shutter. Plywood is allowed in narrow cases for low-rise homes (see below), but it is a poor long-term choice and does not earn the best insurance rating.
Unincorporated Palm Beach County uses the ePZB permit portal run by the Planning, Zoning and Building Department; cities such as West Palm Beach and Boca Raton run their own. The 1928 Okeechobee hurricane made landfall near Jupiter.
The Florida Keys (Monroe County)
The Keys have the highest mapped wind speeds outside the HVHZ. On the UF draft map for Monroe County, the mainland part of the county sits between about the 160 and 170 mph lines, and the island chain runs from about 170 mph in the upper Keys to about 180 mph and higher in the middle and lower Keys. All of it is in the wind-borne debris region.
Monroe County is not in the HVHZ, so HVHZ-only rules do not technically apply, but at these speeds the impact and pressure requirements are often just as demanding in practice. Two other Keys realities affect opening protection:
- Elevated homes. Many Keys homes are raised above flood levels. Windows higher above grade see different pressures, and the FBC's small-missile option above 30 feet applies only to glazing more than 30 feet above grade. ASCE 7-22, adopted in the 2023 FBC, also added new wind criteria for elevated buildings. Ask your designer to use the elevated-building provisions.
- Plywood limits. The FBC plywood exception applies only where Vult is 180 mph or less. Lots at or above 180 mph cannot rely on it.
The Keys' storm history explains the stakes. NCEI says Hurricane Irma (September 2017) made landfall at Cudjoe Key as a Category 4 and that 25 percent of buildings in the Keys were destroyed and 65 percent significantly damaged. The 1935 Labor Day hurricane, a Category 5, came ashore at Craig Key. Permits in Monroe County are handled by the county building department for unincorporated areas and by Key West, Marathon, Islamorada and the other cities within their limits.
Southwest Florida after Hurricane Ian: Lee, Collier, Charlotte and Sarasota
Southwest Florida has some of the highest design speeds in the state and the freshest storm memories. NCEI says Hurricane Ian made landfall near Cayo Costa (Lee County) on September 28, 2022 as a Category 4 with 150 mph winds, and lists its cost at $119.6 billion (inflation-adjusted). Two years later, Milton came ashore near Siesta Key (Sarasota County) as a Category 3 with a 5 to 10 foot storm surge from Naples to Charlotte Harbor.
| County | UF draft Risk Category II range | What it means for openings |
|---|---|---|
| Lee | About 150 to 160 mph | Whole county in the debris region; impact glass or approved shutters on all new and replacement glazed openings |
| Collier | About 150 to 170 mph | Whole county in the debris region; coastal Naples and Marco Island sites face the higher end |
| Charlotte | About 140 to 160 mph | Debris region county-wide on the draft map |
| Sarasota | About 145 to 155 mph | Debris region county-wide on the draft map |
Did Ian change the rules? The design wind speeds for the peninsula did not change in the 2023 code; the Florida Building Commission says they have effectively not changed since the 2010 FBC. For owners repairing after Ian, the bigger rule question is often flood, not wind. Many coastal homes in these counties are in flood hazard areas, which matters because Florida's new $7,500 permit exemption (below) does not apply to property in a flood hazard area.
Charley's lesson. Hurricane Charley (2004) came ashore at Punta Gorda as a Category 4. The Insurance Institute for Business and Home Safety (IBHS) studied Charlotte County homes afterward and found that homes built under post-1996 requirements had substantially fewer insurance claims and significantly lower damage than older homes. That finding is a big reason Florida insurers give credits for verified opening protection; see our insurance discount guide.
Lee and Collier permits. Both counties and their cities (Cape Coral, Fort Myers, Fort Myers Beach, Bonita Springs, Sanibel, Naples, Marco Island) issue their own permits. Products need Florida approval numbers or NOAs, and the permit drawings must show design pressures for each opening. If you are repairing storm damage, ask whether your home is subject to substantial damage review under local flood rules before you order windows, because a substantial damage finding can change what work is required.
Tampa Bay: Pinellas, Hillsborough and Pasco
Tampa Bay sits right on the 140 mph line. On the UF draft maps, all of Pinellas County falls between the 140 and 150 mph contours, so the whole peninsula county meets the debris-region trigger. In Hillsborough and Pasco, the 140 line cuts diagonally across the county: areas to the southwest, closer to the Gulf and the bay, are above 140; areas to the northeast are below it and need protection only if they are within 1 mile of the coast and at 130 mph or more.
This is the region where checking your exact address matters most. Two houses a few miles apart in Hillsborough County can fall on different sides of the line. A contractor who tells you "Tampa doesn't need impact windows" may be right for one address and wrong for the next.
City of Tampa
Tampa's Construction Services Division handles shutters and awnings as their own residential permit category, and some shutter projects qualify for its "Fast Pass, Same Day" application. Permits are filed through Accela Citizen Access. Tampa's Post-Hurricane Permitting Guide (updated April 2026) says permit waivers apply only after a declared disaster and only when the Mayor has exercised emergency powers under City Code Section 2-403. Even then, size-for-size front or rear door replacement can be waived, but garage door replacement still needs a Residential Building Trade permit (with the fee waived during emergency powers).
Pinellas County
Pinellas County's Building and Development Review Services covers unincorporated Pinellas and several partner communities through its Accela portal. Its page lists an "Installation Compliance Letter for Windows, Doors and Shutters" that is required for electric shutter, garage door replacement and window or door replacement field reports and must be completed before a virtual inspection. Cities such as St. Petersburg and Clearwater have their own building departments.
NCEI says Milton (2024) made landfall to the south at Siesta Key, and Helene (2024) came ashore to the north near Perry. Many Tampa Bay waterfront lots are also in flood hazard areas, and flood rules can affect ground-floor windows and doors, so ask about flood requirements before ordering replacements.
Central Florida and Orlando (Orange County)
Orlando homeowners often ask whether they need hurricane shutters at all. On the UF draft map, Orange County sits between about the 130 and 140 mph lines, with the 140 line touching its eastern edge. Because Orange County is inland, the 1-mile coastal trigger does not apply, so most of the county is below the 140 mph debris trigger. That generally means impact glass or shutters are not required by code for a typical house in Orlando. Check sites near the eastern county line with the Hazard Tool.
Not required is not the same as not needed. Hurricanes weaken over land but can still bring damaging winds and flying debris far inland. Many Central Florida owners still add shutters or impact windows for insurance credits, security and peace of mind. The OIR-B1-1802 form rates opening protection the same way everywhere in Florida, and the 2026 version adds a Region question (Region 1 at 140 mph or more, Region 2 at 130 to 139 mph, Region 3 under 130 mph) based on ASCE 7-22 wind speed, so a mitigation inspector will record which region your home is in.
Orlando permits. The City of Orlando offers a residential building permit exemption request under a 2026 state law (HB 803, ch. 2026-63, effective July 1, 2026). The law requires local governments to exempt single-family owners and their contractors from building permits for work valued under $7,500, but the exemption does not apply to property partly or entirely in a flood hazard area or to electrical, plumbing, structural, mechanical or gas work. The owner must submit a written exemption request with the contract. Orlando says it reviews requests within five business days. Whether a particular window, door or shutter job counts as structural is a question for your building department, so ask before you skip the permit. Remember that insurers and inspectors usually want permit records to verify opening protection.
Florida's east coast: Brevard and Volusia
The Space Coast and Daytona area sit along the 140 mph line. On the UF draft maps, Brevard County runs from about 140 mph on its western edge to about 150 mph along the barrier islands, so nearly all of it meets the debris trigger. Volusia runs from about 130 mph inland to about 140 mph near the beaches; sites within 1 mile of the coast meet the trigger, and inland DeLand-area sites generally do not.
Storm history on this coast includes Jeanne (2004, Category 3 at Hutchinson Island) and Nicole (November 2022, Category 1 near Vero Beach), both to the south of Brevard, according to the Florida Climate Center. Late-season storms like Nicole are a reminder that the official season runs to November 30.
Northeast Florida: Jacksonville (Duval County)
Jacksonville has the lowest mapped speeds of Florida's major metros. On the UF draft map, Duval County lies between about the 120 and 130 mph lines, with the 130 line just offshore. Because the coastal trigger starts at 130 mph within 1 mile of the shore, most Jacksonville homes are outside the wind-borne debris region. Beachfront lots near the 130 line should still be checked with the Hazard Tool and the building department.
Jacksonville's Building Inspection Division requires electronic permit submission for all permit types through JaxEPICS (jaxepics.coj.net), and you need a JaxEPICS account to submit. The city also advises homeowners to confirm contractor licenses with the Florida Department of Business and Professional Regulation before signing.
Even without a code requirement, many Jacksonville owners protect openings. Shutters are relatively easy to add later, and the OIR form gives credit for verified protection regardless of region.
The Big Bend and Panhandle after Michael, Idalia and Helene
Bay County and the central Panhandle
Hurricane Michael is the Panhandle's defining storm. The NWS office in Tallahassee says Michael made landfall on October 10, 2018 as a Category 5 with 161 mph (140 knot) sustained winds; NCEI says Mexico Beach was nearly destroyed, with storm surge above 15 feet, and lists the cost at $31.2 billion (inflation-adjusted).
Bay County publishes its own wind-borne debris map for the 2023 FBC. It shows Risk Category II contours at 130 and 140 mph, the debris region where speeds are 140 mph or more, and a separate debris strip within 1 mile of the mean high water line. In plain terms: the coast and western part of the county need impact protection on new and replacement glazing, and some inland northeastern areas may not. IBHS's post-Michael investigation found that modern codes significantly improve resilience but are not meant to prevent all damage in extreme events, and that FORTIFIED homes showed added benefits of building beyond code. See our FORTIFIED guide.
Escambia, Santa Rosa and Okaloosa (western Panhandle)
The western Panhandle is the one part of Florida where design wind speeds went up in the 2023 code, according to the Florida Building Commission. On the UF draft map, Escambia County runs from about 140 mph in the north to about 160 mph on the barrier island. Pensacola-area projects permitted under older maps may have used lower numbers, so replacement work today may need higher-rated products than the originals. Opal (1995) came ashore at Pensacola Beach and Dennis (2005) at Santa Rosa Island.
The Big Bend (Taylor, Dixie, Levy, Wakulla)
The Big Bend shows the gap between code maps and real storms. On the UF draft map, Taylor County (Perry) sits around the 120 mph line, below the 130 mph threshold, so the debris-region rules generally do not apply there. Yet NCEI says Hurricane Helene made landfall near Perry on September 26, 2024 as a Category 4 with 140 mph winds, the strongest on record in the Big Bend, with up to 15 feet of surge. A year earlier, Idalia came ashore near Keaton Beach as a strong Category 3. Owners in these counties are not required to install impact protection on most homes, but many choose to, and a wind mitigation inspection can record the protection for insurance credit.
Statewide rules that apply in every county
Whatever county you live in, these Florida rules apply:
- Product approval. Florida Statutes 553.842 requires statewide approval for windows, exterior doors, skylights, shutters and impact protective systems, and bars marketing a product as hurricane or debris protection unless it is approved. Look up a product on the Florida Building Commission's product approval site or in Miami-Dade's NOA database. See our product approval lookup guide.
- Plywood exception (outside the HVHZ). FBC 1609.1.2 and R301.2.1.2 allow 7/16-inch wood structural panels with a maximum 44-inch span as opening protection on one- and two-family homes (and Group R-3/R-4 buildings) with a mean roof height of 33 feet or less where Vult is 180 mph or less. Panels must be precut, predrilled and attached with corrosion-resistant hardware permanently installed on the building. See our plywood guide.
- Replacement windows. FBC Existing Building 707.4 requires replacement windows, doors, skylights and garage doors to meet Chapter 16. A limited exception lets one- and two-family homes built before the FBC replace up to 25 percent of total glazed area in any 12-month period without opening protection (in the HVHZ, homes built under codes before September 1, 1994).
- Labels. Every approved shutter must carry a permanent label with the approval holder, approval method and Florida or NOA number (FBC 1709.9).
- Condos and HOAs. Florida Statutes 718.113(5) and 720.3035(6) require associations to adopt hurricane protection specifications and bar them from denying conforming installations. See our condo guide and HOA guide.
- Grants. My Safe Florida Home is a statewide program run by the Department of Financial Services. Under s. 215.5586 it requires an eligible homesteaded, site-built, owner-occupied home built before January 1, 2008, with insured value of $700,000 or less, and the applicant must be low or moderate income. As of November 19, 2026 the program's site says the applicant portal has been offline since November 10 while it moves to a new platform. See our My Safe Florida Home guide.
- Licensing. Window and shutter installers need the right state license, and unlicensed contracting during a declared state of emergency is a third-degree felony under s. 489.127. See our licensing guide.
Where to look up your county's permit requirements
Permits are issued by the city if you live inside city limits, and by the county if you live in an unincorporated area. Here are portals we confirmed on official pages:
| Jurisdiction | Portal or office | Notes |
|---|---|---|
| Miami-Dade County (unincorporated, folio begins with 30) | County permitting portal via miamidade.gov Building; Windows, Shutters, Doors and Security Bars page | Licensed contractors can get accordion shutter and storm panel permits through e-permitting |
| Palm Beach County (unincorporated) | ePZB permit portal (Planning, Zoning and Building) | Cities run their own permits |
| City of Tampa | Accela Citizen Access; Shutters and Awnings permit page | Some shutter jobs qualify for Fast Pass, Same Day |
| Pinellas County (unincorporated and partner communities) | Accela portal (aca-prod.accela.com/pinellas) | Installation Compliance Letter for windows, doors and shutters before virtual inspection |
| City of Orlando | Permitting Services Division; online exemption request | Under-$7,500 exemption request reviewed within five business days |
| City of Jacksonville | JaxEPICS (jaxepics.coj.net) | Electronic submission required for all permit types |
| Bay County | Bay County building department | Publishes a 2023 FBC wind-borne debris map |
For any other county, search for "[county name] building division" on the official .gov site, and ask three questions: which adopted wind speed map applies, whether your lot is in the debris region, and whether your parcel is in a flood hazard area. Our Florida permit guide covers what to submit.
Florida's 2026 code update: what changes on December 31, 2026
The Florida Building Commission has been developing the 9th Edition (2026) FBC. Miami-Dade County says the 9th Edition takes effect December 31, 2026, and that plans submitted on or after that date must comply with it. For window and shutter buyers, the practical effects are:
- If your contract is signed in late 2026, ask your contractor which code edition the permit will be reviewed under.
- Product approvals are tied to code editions and test standards. Confirm that the approval numbers on your quote will be valid for the edition your permit falls under.
- Wind speed maps, the debris-region definition and the HVHZ county list could be revised in the new edition. We will update this guide when the final text is published. Until then, the numbers above reflect the 8th Edition (2023).
How to choose a provider
- Confirm whether you are in Miami-Dade or Broward (HVHZ) or elsewhere.
- Look up your Risk Category II wind speed on the ASCE 7 Hazard Tool using ASCE 7-22.
- Ask your building department for its adopted wind speed and debris-region map.
- Apply the debris test: 140 mph or more, or 130 mph or more within 1 mile of the coast.
- Check whether your parcel is in a flood hazard area before relying on any permit exemption.
- Get the Florida approval number or Miami-Dade NOA for every product on the quote.
- Confirm the permit will be filed with the right city or county office.
- For condos over three stories or 50 feet, budget for the threshold inspection now required.
- Ask which code edition (2023 or 2026) your permit will be reviewed under.
- After installation, schedule a wind mitigation inspection and keep your NOAs and permit records.
Related hurricane shutters and impact windows guides
- What Is the HVHZ? Hurricane Protection Rules in Miami-Dade and Broward vs. the Rest of Florida
- Florida Building Code Opening Protection Rules: When Is Impact Protection Required?
- Design Pressure (DP) Ratings Explained: What Do DP50 and +60/-70 psf Mean for Your Windows?
- Do You Need a Permit for Impact Windows, Doors and Shutters in Florida? Process, Documents, Fees and Inspections
- Replacing Windows in an Existing Florida Home: Does the New Window Have to Be Impact Rated?
- Wind Mitigation Form OIR-B1-1802: How Is Opening Protection Graded (Classes A, B, C, N, X)?
- Does My Safe Florida Home Pay for Impact Windows and Doors? 2026 Eligibility, Match and Status
- Hurricane Protection on the Texas Coast by County: Galveston, Houston-Area Cities, the Coastal Bend and the Rio Grande Valley
Hurricane shutters and impact windows by state and city
Questions people ask
Do I need impact windows in Palm Beach County?
For new construction and replacement windows, yes in practice. Palm Beach is not in the HVHZ, but its mapped Risk Category II wind speeds run from about 150 to about 170 mph, above the 140 mph wind-borne debris trigger, so glazed openings must be impact rated or covered by an approved shutter. You can meet the rule with shutters instead of impact glass, and plywood is allowed only in limited low-rise cases. You do not have to retrofit an existing home that you are not working on.
What are hurricane shutter rules in Miami-Dade?
Shutters must have a current Miami-Dade NOA or a Florida approval covering HVHZ use, must pass TAS 201, 202 and 203 testing, and must carry a permanent label showing the approval number. Licensed contractors pull accordion shutter and storm panel permits through the county's e-permitting system, and owners inside a city file with that city. Plywood is not an approved option in the HVHZ. If you live in a condo, the association's adopted hurricane protection specifications also apply.
Do Orlando homes need hurricane shutters?
Generally not by code. Orange County is inland and sits between about 130 and 140 mph on the draft wind map, so most of it is below the 140 mph debris trigger and outside the 1-mile coastal strip. Sites near the county's eastern edge should be checked with the ASCE 7 Hazard Tool. Many Orlando owners still add shutters or impact windows for insurance credits, security and peace of mind.
Do coastal Jacksonville homes need opening protection?
Usually not by code. Duval County lies between about the 120 and 130 mph lines on the draft map, with the 130 line just offshore, so most homes are below the coastal debris trigger of 130 mph within 1 mile of the shore. Beachfront lots near the line should be confirmed with the Hazard Tool and the city's Building Inspection Division. Permits are filed online through JaxEPICS.
Which Florida counties are in a windborne debris region?
No county is entirely in or out except by the mapped wind speed lines. Based on the draft county maps, essentially all of Miami-Dade, Broward, Palm Beach, Monroe, Collier, Lee, Charlotte, Sarasota, Pinellas, Brevard and Escambia meet the trigger. Parts of Hillsborough, Pasco, Bay and Volusia do. Most of Orange, Duval and Taylor do not. Confirm your address, because the official line follows your county's adopted map.
Do Florida Keys homes require impact windows?
Yes for new and replacement glazed openings. Monroe County's mapped speeds run from about 160 to 180 mph or more, so the whole county is in the debris region. Impact glass or approved shutters both satisfy the rule. Lots at or above 180 mph cannot use the plywood exception, which applies only up to 180 mph. Elevated homes may need designs that use ASCE 7-22's new elevated-building provisions.
Do Monroe County rules differ for elevated homes?
The same opening protection rules apply, but elevation changes the engineering. ASCE 7-22, referenced by the 2023 FBC, added criteria for elevated buildings, and windows high above grade face different pressures. The small-missile option applies only to glazing more than 30 feet above grade, which few single-family homes reach. Flood rules also govern what can be built below the design flood elevation. Ask your designer and the building department before ordering products.
What are Lee and Collier County rules after Hurricane Ian?
The opening protection rules did not change after Ian. Both counties are entirely in the debris region on the draft maps (about 150 to 160 mph in Lee and 150 to 170 in Collier), so new and replacement glazed openings need impact protection. For storm-damaged homes, flood rules, including substantial damage reviews, can change what work is required. Pull permits with the county or your city, such as Cape Coral, Fort Myers, Naples or Marco Island.
What are Panhandle rules after Hurricane Michael?
Bay County's 2023 map shows 130 and 140 mph contours, with debris protection required where speeds are 140 mph or more and within 1 mile of the coast. In the western Panhandle, the 2023 code raised wind speeds, so Escambia now runs from about 140 to 160 mph and most of it is in the debris region. Older homes being re-glazed may need higher-rated products than the originals.
Do Tampa Bay homes require impact protection?
It depends on the address. All of Pinellas County is between the 140 and 150 mph lines, so it is in the debris region. In Hillsborough and Pasco, the 140 line crosses the county; southwest areas near the Gulf and bay are in, and northeast areas are generally out unless within 1 mile of the coast at 130 mph or more. Check your address on the ASCE 7 Hazard Tool and ask the building department.
What wind speed applies in my Florida county?
In Miami-Dade and Broward, the code fixes Risk Category II speeds at 175 and 170 mph. Elsewhere, look up your address on the ASCE 7 Hazard Tool using ASCE 7-22, then confirm with your building department's adopted map, since many counties adjusted the lines to roads and canals. Do not use the older ATC Hazards by Location site; the Florida Building Commission says it does not support ASCE 7-22.
Does the $7,500 permit exemption cover new windows or shutters?
Possibly, but check first. Ch. 2026-63 requires local governments to exempt single-family work under $7,500 from building permits starting July 1, 2026, but not for property in a flood hazard area and not for structural, electrical, plumbing, mechanical or gas work. You must submit a written exemption request with the contract. Ask your building department whether your window or shutter job qualifies, and keep in mind that insurers and wind mitigation inspectors rely on permit records.
Will the 2026 Florida Building Code change these rules?
Miami-Dade says the 9th Edition (2026) FBC takes effect December 31, 2026. Final changes to wind maps, the debris definition or approvals should be checked when the edition is published. If your permit will be filed near that date, ask your contractor which edition applies and confirm that the product approvals on your quote are valid under it.
Sources
- Florida Building Code, Building, 8th Ed. (2023), Chapter 2 Definitions (UpCodes)
- Florida Building Code, Building, 8th Ed. (2023), Chapter 16 Structural Design (UpCodes)
- Florida Building Code, Residential, 8th Ed. (2023), Chapter 3 (UpCodes)
- Florida Building Code, Existing Building, 8th Ed. (2023), Chapter 7 (UpCodes)
- Florida Building Code, Building, 8th Ed. (2023), Chapter 17 (UpCodes)
- Florida Building Commission, Wind Loads: Impacts from ASCE 7-22 fact sheet (June 2024)
- Florida Building Commission, FBC Supplement: Annual Technical Amendment summary (wind-borne debris definition)
- University of Florida GeoPlan Center, Draft Final Report: Wind Speed Line Maps for the FBC 8th Edition (June 8, 2023)
- University of Florida GeoPlan Center, Preliminary countywide Vult maps, FBC 2023 (March 22, 2023)
- Bay County, Wind-Borne Debris Map, 2023 FBC 8th Edition
- Florida Building Commission (BCIS) home page
- Florida Statutes 553.842, Product evaluation and approval
- Laws of Florida ch. 2026-63 (CS/CS/HB 803)
- Florida OIR Form OIR-B1-1802, Uniform Mitigation Verification Inspection Form, Rev. 04/26
- Miami-Dade County Building Department home (9th Edition notice, threshold buildings)
- Miami-Dade County: Windows, Shutters, Doors and Security Bars
- Miami-Dade County: Homeowners general permit information
- Miami-Dade County: Product Control Search
- Palm Beach County PZB Building Division
- City of Tampa: Shutters and Awnings permits
- City of Tampa: Post-Hurricane Permitting Guide (April 2026)
- Pinellas County: Building and Development
- City of Orlando: Apply for a Residential Building Permit Exemption
- City of Jacksonville Building Inspection Division
- Florida Statutes 215.5586, My Safe Florida Home
- My Safe Florida Home
- Florida Statutes 489.127, Prohibitions; penalties
- Florida Statutes 718.113, Condominium hurricane protection
- Florida Statutes 720.3035, HOA architectural control and hurricane protection
- Florida Climate Center (FSU): Hurricanes
- NOAA NCEI: Billion-Dollar Disasters, Florida summary
- National Weather Service Miami: Hurricane Andrew
- National Weather Service Tallahassee: Hurricane Michael
- IBHS: Hurricane Charley Building Performance Report
- IBHS: Post-Hurricane Michael research
This guide was written by our editorial team from the public sources listed above. It is general information, not legal advice; confirm licensing and terms directly with any provider.


